Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Dear All,
while evaluating low-power options in the context of wireless sensors, I've stumbled upon a strange behavior with the nRF52832 using ESB from SDK 14.2. Here's...
Hi
I modified the SPI master example to read an 16-bit ADC at 44.1 kHz.
While the HAL_TIMER achieves its ~22 microseconds quite good, the SPI driver is quite slow: the...
Hi!
I have an observer that listens for advertises from just one ble switch. I can control the leds on the nRF52 DK with the switch. Now i want to connect to nrf connect...
Hey guys,
I have been fighting with this for a couple of days and I am hoping someone can give me some insights as to what might be going on.
We currently use the nRF24L01P...
hi,
i am doing a project where i have to discover custom services on connected ble nodes.
i am using nrf52832 as central device and thingy 52 as peripheral device i have...
Hi Nordic:
I build up an mesh network with following setting:
1. A nRF52 platform with example/light_switch/provisioner with a auto-start-provisioner
2. Another nRF52...
Hi,
I have successfully used the nRF Connect app with a Rigado BMD-350 Dev Board to send a few UART characters back and forth to a new target device using the Rigado BMD...
I started today with the following examples to make a start with serialization:
- ..\examples\connectivity\ble_connectivity\pca10040\ser_s132_hci
- ..\examples\ble_peripheral...
HI:
I am Measuring current on custom hardware with nRF5x DK, Peak current is always too high during testing.Please give me some advice。
I am using the nRF52 DK development...
Hi,
I am working on RTC implementation. I had a doubt.. Is it possible to generate interrupts on different channels (channel 0/1/2/3) using same RTC instance ?
Thanks
Hello,
I'm trying to communicate with another device via I2C. I'm trying to do a simple write but it seems that the TWI NRFX driver is sending wrong data.
I'm just calling...
Hi,
I am implementing a beacon solution and intrested to move from fast to slow and vis versa(slow to fast) advertising modes -
i.e. BLE_ADV_MODE_FAST & BLE_ADV_MODE_SLOW...
Hey,
I have seen some articles which says that voice over BLE (4.0) is possible but there is no standard profile for it.
So far i've seen :
Silicon Labs
STM
T.I...
Hi,
After I reset nrf8001, RDY pin stays hi. I checked the crystal pin, there is no clock. I am using TSX-3225 from Epson with 12pf caps.
Am I suppose to see the clock...
Hi,
I am working on a new project with the secure bootloader (SDK 15) as a part of it. I want to add periodic task that will do several actions for example maintaining the...
