I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Why is the event length of the BLE Central HRS demo set to such a high value of 320*1.25ms = 400ms?
The demo seems to work ok with the BLE Peripheral HRS demo using the...
Does the Battery Service Client (ble_bas_c) module handle subscribing to notifications from multiple slaves? In my use case, I have the nRF52840 dev kit connecting to multiple...
I need to keep track of time on a device featuring the nRF52 and have an RTC run continuously in the background. The drift should not be more than a few seconds over a year...
Hello I try to use P0.09 as GPIO with this simple code but not working. (Works well with pin P0.08)
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include...
Hello,
I use the bootloader from the SDK SoftDevice 14.0.0.
I use the Laird module BL652 which have a nRF52832 component without external clock.
To compile the bootloader...
Hello Everyone,
I am working on nRF5 14.1.0 SDK, My question is how to generate "ble_app_buttonless_dfu_without_bonds_s132.zip" dfu file.
Can any one tell me the exact...
I am using nrf52832_xxaa and SDK 14.2.0.
Does app timer play a role in power optimization?
If yes, Can reducing the app_timer frequency reduce the power consumed by the...
Is there a BLE mesh SDK for nRF52840, and if yes is there anybody tested it? I'm going to switch to the nRF52840 from nRF52832 and it is very important for me to know it is...
Fanstel BT832 module mesh client stuck in nrf_mesh_sdk.c, 187, Initializing softdevice. When I upload the code on the NRF52 DK It works, but when I upload with segger embedded...
I have set up an environment to upload data to the nrfcloud using nrfconnect and the nrf52 dk.I can only upload data upto ff and then it resets to zero .The value which i...
Hello,
I`m searching for a possibility to detect a possible Flash corruption caused by a Brown out or something else? Is there any controller interal possibility to detect...
hello all
This is one of the point that causes me problems into my migration: I figured out the new logs and the SD obbervers... now this:
the 52832 advertises correctly...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Dear.
In my project using twi function(nrf_drv_twi_tx, nrf_drv_twi_rx).
I am faced with parameter problem that length(uintt_t) of nrf_drv_twi_tx function.
I want...
