Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
i'am using nRF52840 (S140 v 5.0.2-alpha) DK and SDK 14.2.
i'am trying to create an application for Beacon which can advertise on 2 different MAC adresses, is it possible...
Hi DevZone,
I am working on a CAN Bus library for communication between nRF52840 Preview DK and MCP2515 chipset. I am trying to modify base on an Arduino MCP2515 CAN Bus...
I am using SDK 14.1.0 S132 for PCA0040 board
i want to combine the next two examples:
examples\ble_peripheral\ble_app_buttonless_dfu
and
examples\ble_peripheral...
Dear experts,
How is the UCIR protected against rewriting?
I would like to store some ID's which I want to be sure they cannot be erased or over-written once programmed...
Hello,
I can see s110 api commands as a web pages on infocenter.nordicsemi.com .
Is it an api list of commands manual in a document like pdf, etc.?
Thanks.
We are trying to configure the I2S peripheral for working with the ICS-43434 microphone ( www.invensense.com/.../) , but we are having a hard time fulfill the requirements...
The product spec is not clear, what is the maximum current draw possible from a 52832? Please assume ALL features are in use and fully enabled.
Thanks.
Hi Dev Zone,
I am going to communicate my nRF52840 Preview DK with an arduino shield. I am checking the PIN number. According to the information about the Arduino board...
Hello, I want to switch the functions between beacon advertising to connectable advertising.
In the code , it can be initial as a beacon advertising or normal advertising...
Hi,
I am running the ble_app_beacon example in nRF52 DK (PCA10040). I can see the nRF beacon in nRFConnect app - but not in the nRFToolbox - Beacons. After opening the app...
Hello,
I am using WT51822-S4AT based on the nRF51822 SoC and I am trying to program it with the ble-beacon example from the SDK. Looking at the DK documentation, I need...
Hi,
Device- nRF52832 (nRF52 DK)
SDK version 14.2
SoftDevice version 5
Segger embedded studio.
I am trying get the BLE working, unfortunately calling nrf_sdh_enable_request...
Hi, Everyone How to turn on 4 LEDs in BLE ? I am testing ble_app_uart on nrf52832 (softdevice s132). Try to blink the four LEDs on the board do. I have added to main() bsp_board_led_invert...
