Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hi am using NRF52 board ...and am trying to send data(which is not a string) using ble_bus_string_send . I send data only once from a one second timer but the other side is...
Hi all!
I'm working on an nrf51822 (technically right now I'm using the PTR5518 as I'm still prototpying), and trying to set up a voltage divider on my pcb in order to...
Hi,I am debuging my programm base on SD-110-V6.0.0 ,sdk-V5.2.0. When I use the
static void characteristic_disc_req_send(const ble_ans_c_t * p_ans, const ble_gattc_handle_range_t...
Hi everyone,
I have a nrf51-dk. I am running Master Control Panel app on my win7 computer. However, I cannot see my nrf51-dk in discovered devices section. Log says, Loading...
I am working on an application for the nRF52 Preview board, using SDK 0.9.2. I need to acquire about five analog samples from a single channel at roughly 100 Hz, then wait...
I use SDK9.0,SD8.0,the device is 51822AC,the device can enter to Bootloader mode.
As it shows below.
Then I selected the .zip file to start DFU
But when it reached...
I'm trying to do all my development on linux, mostly so that I can use a continuous integration environment. I'm setting up a server to compile my firmware app on every pull...
Hello I am currently using the NRF52 DK2 PCA10040 with S132 soft device (nRF52 SDK v0.9.2) . I have setup my code to sample 4 analog pins periodically. I configured double...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I tried it from my Nexus 5, using the Android version of MCP. I can connect/unconnect, detect link loss, and (apparently) everything else, but only LED 1 seems to behave...
I want to connect one peripheral to a few central devices (lets say 3) but the central devices don't need to be connected to the peripheral at the same time. Should the PERIPHERAL_LINK_COUNT...
