I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I am estudying and modifying the light switch example.
the example shared in the SDK, this example works as star network. (1 client and 3 (or many) servers) where:
- The...
Hi,
I' writing an app based on ble_thread_dynamic_template with added CoAP utils, but with a few changes. Program works fine, I am able to communicate over CoAP, but after...
Hello!
Last time I've described issue with connection problems in large thread network https://devzone.nordicsemi.com/f/nordic-q-a/29867/thread-mesh-network-capacity-problem...
Hi,
I have encountered a 404 error:
<<<
HTTP ERROR: 404
Problem accessing /help/pdf/nwp_017.pdf. Reason:
ProxyServlet: /help/pdf/nwp_017.pdf
Powered by Jetty...
Hi,
I am trying to send stream of data over BLE. I am using nRF52 development kit and in that ble_app_uart code is running. I want to send continuous data to the UART and...
I am using PPK 1.1.0 to compute current draw on a custom hardware.
If I upload ble_app_hrs example on the nRF52-DK and measure it directly, I obtain average reading as 550...
Dear all,
sorry for asking a very beginner's question but I'm really a beginner and want to understand what I'm doing :)
What I have:
nrf52 DK
nrf SDK11.0.0...
Hello,
we are using the USB CDC ACM Example to set up a USB connection between the computer and the nRF-Chip.
By pressing Press Button 1 a bunch of test data will be sent...
Hi!
Is there any programming guide for establishing mesh network? I want to develop from scratch but i can't find any document for programming to mesh network. I seen Light...
Hi
I am able to successfully compile my C++ code on Raspberry Pi3 however while running an executable file. I am getting below error.
pi@raspberrypi:~/RF24/librf24-rpi...
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
Hello Nordic Devzone fellowes
I tried DFU with NRF 52 DK board with 'PC-BLE-DRIVER-JS' dfu.js test code
When the firmware .zip file is 128 KB the speed of transftering...
Hi, Everyone
I am developing based on ble_app_uart at nrf52832 (softdevice s132)
I modified the program slightly.
- After the connection is confirmed
- Send 100 bytes...
Hi Devzone:
I have build up a environment that are
1. a thingy52 with mesh-briadge
2. a thingy52 with mesh-node, which is control by segger-debugger, and it shows
...
