hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
How to write a byte in flash by using
static void flash_word_write(uint32_t * p_address, uint32_t value) function
while in a advertising mode.
I tried to call the...
Hello.
Here is my conditations;
using ukeil 5.
sd132 Version 5.
sdk version 14,2,17b948a
In my project, i am using secure connection. So peer manager...
Hello Guys,
I am newbie to nrf51822 programming. Currently using nrf51822 (raytac's MDBT40) with S130, SDK11.
I am programming the nrf51822 using arduino IDE using this...
Hi,
I'm seeing this error PM_EVT_PEER_DATA_UPDATE_FAILED sometimes and I need to understand what are the options on handling this error except for just asserting it. I...
Hi,
We have to implement a nRF to nRF DFU. On the nRF51 side a have an external memory with two bankers to perform secure update and downgrade using a bank 2. Now, we are...
when scan the BLE device, screen can look the device's name, but the time parameter is means?
ex:
-31 dbm <-> 1010ms
1010ms means? is about dbm power value>
thks...
We have field reports of BlackBerry Priv not being able to "connect" to our nRF52 based hardware.
BlackBerry Priv is: www.gsmarena.com/blackberry_priv-7587.php
(Runs...
I use same SDK to program the 1.nRF52_DK borad (on broad chip 52832) ,and 2.external program borad chip 52832.
Have a issue, 1.nRF52_DK borad is success to advertisement...
Hey!
Using osx, SES 3.30, importing experimental_ble_app_blinky example from nRF5_SDK_11.0.0_89a8197 to be used with NRF51822 chip. When importing I chose pca10028/s130/iar...
Hello
I am testing with the lis2dh12 sensor and our custom board. I made the LCD test successfully. So I tested the lis2dh12 sensor based on the LCD code, but it failed....
Is there a comprehensive explanation of the usage of uuids_complete, uuids_more_available & uuids_solicited when to use them and how the stack behaves/uses them. I getting...
Hello
First of all, I would like to apologize if a similar question was already asked but all this BLE matter is so broad that it defeats me.
I am planning to put two...
I try to use Eclipse for my nrf project. Previously I used Keil but now, I should to use Eclipse. Anyway, I can build nordic sdk example project but when I work with main...
Hi,
I have posted the same question in the following URL.
devzone.nordicsemi.com/.../
It will be very helpful if you tell me how to get a correct MIC result by AES...
