Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
This fork of the MBED CMSIS-DAP firmware seems to be the latest updated one. The title says, 'Interface firmware providing USB CMSIS-DAP for debugging, USB MSD for programming...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...
I have 2 existing products, one using the nRF24LE1 and the other having a 2.4GHz ANT radio. Is there a way to have the 2 products communicate wirelessly? If it is possible...
Hi.
Quest to get the toolchain working under ubuntu continues.
I've done the eclipse and jlink config as explained in the nrf51 linux tutorial (with of course keeping...
In an RFID application, we have nrf24l01+ and SMT32F4xx on the Reader and nrf24lu1+ on the tag.
The Reader is acting as multiceiver currently.
Pipe 0 and Pipe 1 are...
Hi Team,
Is it possible to develop MCP like other application which runs on Linux (say Ubuntu) using BLE dongle?
Where to start for this!? Any guideline or documentation...
Can smone help me:
An error pops-up…
“
RESTRICTED VERSION WITH 0800H BYTE CODE SIZE LIMIT; USED: 0DC4H BYTE (172%) *
“
This could be due to EVAL version of uVision...
So I'm using Keil v5.18.0.0, MDK-Lite Version 5.18, nRF Beacon app version 1.4.2, android 5.1.1, nRF51822, and nRF52832 micro-controller
I can successfully connect te bluetooth...
I use nrf51822qfaa ,s110 V8.00,keil mdk V5 ide.
does advertizing data Length can more than 31 byte? why?
ble_advertising_init(&advdata, &respadvdata, &options, on_adv_evt...
hello everybody,
I'm working in a project and faced some problems : article_1 & article_2
the final thing I did is as the second article, I do bonding & added the whitelist...
I want to make a BLE central A that can only connect to a BLE periperal B, and central A can not connect to periperal C,D,E...and other devices, even if they have the same...
Hi Nordic support,
I check the serialization page ( infocenter.nordicsemi.com/.../lib_serialization.html)
And prepare a connectivity board as below for my host system....
