Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
Hi, we are using
'iOSDFULibrary' , '~> 3.0' for firmware updation process. we are getting "DFU not found" error when device is already in dfu mode at the time of update...
Hello,
I've got the light_switch example running. I would like to extend this example with the possibility to send a broadcast messages from every node, the light client...
Hi, We are facing issue with updating firmware using NordicSemiconductor/IOS-Pods-DFU-Library. we are unable to upload new firmware and getting failed operation at the time...
Hi,
although the NRF52840 has a nominal receiver sensitivity of -103 dbm I am only able to get a sensitivity of around -97 dbm. I know there was a bug in older soft device...
Hi all,
im using keil5 for this .i getting problem or may be confusion while selecting the packages .also could i use the softdevice for this .Also wanted to know the uart...
I want use two 52DK for BLE transfer demo, one 52DK download nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart",
other 52DK download "nRF5_SDK_15.0.0_a53641a...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device. Schematics are shown below
here BATTERY is connected...
The nordic thingy won't program anymore every time I try to program it gives an unknown error.
Does this mean that it is bricked and i need to change the chip or is there...
hi,
I am trying to develope a code to blink 2 LED's for different time interval of 500mS and 800mS using TIMER but I want to control them using TIMER 0 for one LED and TIMER...
Good afternoon,
I would like to ask you if it is actually possible for the peripheral device to automatically repair with the central device after being powered off through...
Hi All,
I have an application successfully running on nrf52832 with sd132 which I am migrating to nrf52810 sd112. Unfortunately since the softdevice structure has changed...
