We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
I'm investigating the flash usage by the peer manager to store bond related data. While I haven't had a chance to fully investigate how the FDS and fstorage modules work,...
Hi,
We have a need to have a Nordic app for nRF51822 which both serves as a beacon and also offers a connectable service.
It's my distinct impression at present we cannot...
Hi,
My setup :
nRF52832
Soft Device S132 v5
SDK14.2
My use case involve me to send data to to a central device at 50 meters. I need to send only a small data...
Hello everyone :) , I work on a project initialy configured for a PCA10040 board and I would like to use the debug with my PCA10056 board but unfortunatly the debug doesn...
Hi
For some reason I get stuck in softdevice at 1EA7A when a send some random data to my phone also I notes that function sd_ble_gatts_hvx return 3401
PC = 0001EA7A, CycleCnt...
I am trying to connect thingy as peripheral and many smartphones as central but i can connect only one smartphone by using thingy at a time.Is it possible to connect many...
[References]
In page 234 of nRF52832_PS_v1.4 it says "In both modes, the TIMER is started by triggering the START task, and stopped by triggering the STOP task."
In this...
I am trying to add a custom service to support a communication path in my project. The Nordic UART example gives a good place to start so, using that as a template, I have...
Hi All:
i met a trouble.
i want to implement a function that i can restore mesh device by uart cmd.
so , i add uart to light switch service demo, when i recive a cmd...
Hi,
I tried the BLE Uart example on my own nRF51 board, but after a few minutes the application hangs in the softdevice.
The board is one we developed, an FTDI cable...
Is there a way to retrieve 128-bit base UUIDs from the SoftDevice, either the "built-in" Bluetooth SIG standard or a vendor-specific one registered via "sd_ble_uuid_vs_add...
Hi,
I'm having problems running the ble_peripheral/ble_app_blinky example with my iPhone 7 and nRFConnect. Here are the specs for the tools I'm using:
nRF52-DK: PCA10040...
