Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'd like to run the DK in at the lowest power in SYSTEM_ON mode.
It's my understanding that the ble_app_gzll example places the system in the "low power" SYSTEM_ON mode...
Hello Folks
I would highly apprciate if anyone can point me in the right direction here
After lot of consultation we imported a smal size shipment (of about 1000 nRF51822...
Connection_mode_with_1sec_Notification.jpg
In my BLE project I am using connected mode, and I found that the current consumption is very high ~190uA during idle mode. I...
I'm currently working with an own hardware with a nRF52840. We had some time to get the radio working, because we copied the schematic of the PDK. In the reference design...
Hello I am using sdk version 14.0 and softdevice S332. I am looking at the ANT + bsc code. I have two questions when looking at this code.
bsc_tx could not see an event...
Hello guys,
Please help me on this.
I want to erase BMD 350 chip using BMD 300 erase and recovery software tool. But I can not do it.Error comes as per the attachment...
Dear all,
I want to create a star network, composed by one gateway and a limited number of nodes. The nodes periodically send information to the gateway. I am using the...
I'm running the HID Keyboard example from SDK 12.2.0 on nRF51-DK with SD 130.
When I long push Button1, it disconnects for a moment and connects again immediately.
Events...
I am trying to make a custom application in which I need to connect to a device and read/write its characteristics' value.
But my target device has had 4 primary services...
Hi Nordic Engineers!
we bought 110 nRF52840 IC's for Field tests.
10 of them marked Q1AAAA / 1716AK
another 100 marked Q1AABB / 1745AC
What is difference between series...
Dear Nordic Team,
Thanks for supporting.
Now i am work with secure dfu using SDK12.3.0.
My Hardware :PCA10028
nrfutil version 3.1.0
Create Zip file like : nrfutil...
Hello.
I want to design a product. It will have these features;
It has 4 buttons on it.
Obviously it is battery powered device.
I want to see some information...
Hi
I have made ble scanner using nrf52 and I have set uart baud rate 921600 and sending scanned beacon to other micro-controller for processing but It does not scanning...
Hi
I'm looking for an example on how to write a hex-file to SoC using nrfjprog.dll.
The P/Invokes are all set and working fine.
I'm absolutely not familiar with python...
Hello,
In our project we want use a large characteristic with notification property.
I use a " ble_app_template " project from nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
