Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I just integrated CMock which is part of my unit testing framework and i am trying to test a mocked function however i am running into RAM overflow error. Is there a way to...
May need to post this question to Segger, but I'd figure I'd ask here.
Have a nRF52832 project that compiles, links, and runs fine on the 52832/10040 dev kit board.
...
Hi All,
I am using the nrf52840 to run an application which does not use the BLE.
I need to add firmware update capability to the device so that I can push updated in...
Hi, I am running into a connection problem with connecting to the Secure bootloader example in SDK v13.1, whenever I try to connect I get Gatt 133 error. To my memory, the...
hi,
i doing a project where i have combined light switch server from nrf_mesh sdk 1.0.0 with nrf5 sdk 14.2.0 ble_uart_example to send.
my aim is to send on_off command...
We currently have an application that is running SDK 12.1 on the NRF52832. We have no issues doing a firmware update using the iOS SDK. What we are seeing is a long delay...
Hello, I am running bluetooth example.
I am using the nRF52832 board and SDK 14.0.
I modified the multilink example to make a slight modification and connect it to another...
I have a windows side application and an Android App, both of which are set to capture data from the Thingy Sound Service.
On the windows application, the data after being...
I need to be able to reserve some flash to permanently store manufacturing values that will never change. I did this on an nRF51 by reserving a 4KB block and setting the necessary...
Hi all ,
I have problem . I have 1 NRF52832 dev kit . It connect to STM32 devkit via UART . I want to tranfer firmware of STM32 from smartphone to NRF via BLE , and from...
Hi,
I added this in SystemInit() (just below the CONFIG_NFCT_PINS_AS_GPIOS section) within system_nrf.c so that I could easily turn on or off the APPROTECT read back protection...
I am using Thingy 52 and I need to use multiple sensors on the board. But the API reference is really poor and there is no examples on this. So I don't know how to configure...
I'm trying to debug a high current issue on a custom board based on the nRF52832. I'm currently loading a modified blinky app (entire main.c included below). On the nRF52DK...
hello,
I am using nrf52 DK and MPU 9255 .I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in...
