Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I tested the Heart Rate Monitor sketch code (Arduino Primo IDE code) and verified that it works with the Heart Rate Monitor through the "nRF Toolbox app" on my iPhone. I would...
There have been several topics on limitations on ADC sampling rate when BLE is in connection.
However, I didn't see notes applicable to the following case:
nRF52832, sampling...
Hello all,
I have some troubles to initialize the micro SD card with my custom board.
I have used the nRF 52 DK to write a basic code and do some test. For micro card...
I am using nrf52832 DK and am unable to build my light switch example. It throws an error that some files are not included. In the screenshot, you could see the error. I have...
Hey Everyone
I have written a code for using lora rn2483 with nrf52840 using the uart protocol which is configured on 7 and 5 pin. The program was working fine untill i...
Hi,
I am using the nRF52840 DK and the wireless_uart example from nRF5_SDK_15.0.0 to try and receive data from other 802.15.4 sensors. Using the example I can receive messages...
Hello everyone!
I'm very shy to ask probably a stupid question, but...
I'm trying get abitity to change pwm signal via ble.
I've created service, characteristic, then I...
Hello,
I am trying to get a low consumption and I detect that the activation of the ADC increases the consumption. So I am trying to configure the ADC and when I make...
NRF52832 / S332 / SDK 14.2
Step 1: connect to mobile phone as Peripheral Role, and the connect handler of service was #0 that equal to Peripheral-connection handler number...
Hello,
We are using nRF5 SDK14.2.0 and soft device s132, and trying to perform DFU of the Bootloader itself.
The process fail in nrf_dfu_postvalidate() due to wrong HASH...
i am trying to Connect a custom board with the nrf52 over the bluetooth. nrf52 is running with the BLE_nus
.i am trying to connect it with the uuid in the program is like...
Hi. I`m trying to connect two Nortdic Thingy device and receive data in same time(ex. temperature, humidity etc..).
In my application, I can connect two devices in same...
I have most of the SDK up and running with my firmware, but I cannot find where to limit the number of bonded devices to my module.
I could live with just deleting all the...
Hello,
Is there a way to get the output log for the Mesh Light Switch Demo to output over UART instead of RTT? We are using a Fanstel BT832X module containing an nRF52832...
Hello,
I am currently trying to implement SAADC sampling from three channels into the same sample buffer (device is a 3-axis accelerometer, ADXL335). The root objective...
