Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hallo
We want to update the firmware over the air (BLE).
What is a safty concept?
Our firmware need about 60KB flash ROM.
What have we to calculate for BLE software?
...
Hello Everybody,
I have a question about nRF51422. I want to monitor the ANT+ message from any sensor, which is already connected with the device,
Scenario : if it is...
Hello,
Im trying to create a synchronisation method for sensors using BLE. At the moment i can synchronise them within 10ms accuracy, in theory it should be within 2ms...
Dear all:
same as this issue:
devzone.nordicsemi.com/.../use-dfu-to-update-ap-over-ble-single-bank
it seem same as my way that modify modify "dfu_dual_bank_ble" target...
A big update this week for our S110 SoftDevice. Full OTA DFU for SoftDevice and Application. Also Multi-acivity concurrency for Bluetooth Smart and 2.4GHz protocols. As Developers...
Hello
I got my nRF51422 DK, and got few inquiries
For ANT,BLE DK, where can i find API documentation?
BLE can be implement on nRF51422 DK?
Is there sample project...
I have a 'fresh' nRF51822 on a board and it's not clear to me what procedure I need to follow in order to get it to work. I'm using the Segger programmer and I can program...
In the Keil debug interface, how can I find if the application is throwing an ASSERT, and which it is? I'm using the S110 softdevice. (See other question for context devzone...
Hello, I have a weird problem, the nRF24L01+ is sending a TX PAYLOAD that was left in the TX FIFO (clocked with W_TX_PAYLOAD) as an ACK PAYLOAD when switching to PRX mode...
hello everyone,
i am trying to use SDA and SCL pins of TWI other than 24 and 25, is it possible? i want to know before using other pins for twi other than 24 nd 25 with...
Hi
I try to communicate with others TWi devices using the twi_hw_master driver.
When i initiate a communication with twi_master_transfer , i don't receive any ack from...
Hi,
I have purchased the nRF8001 Development Kit and so far I wired the nRF2740 board to a FTDI VNC2 microcontroller. I have been reading about how to configure the 8001...
Hello. I'm trying to port the ble_hrs to a custom board with an NRF51822 on it, but the advertising never starts. While I'm debugging this, what should I be looking out for...
Is there an example for sleeping? I just want to put this thing to sleep drawing minimum current and have it wake up on a RTC timeout, but do not seem to be able to achieve...
