Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi,
I'd like to embed the nrf.exe utility used for creating DFU packages and uploading firmware via serial in a 3rd party app for use with our Nordic based devices.
...
Hello all,
I wish to set up the nRF51422 so that I can communicate with it via UART using the HCI protocol - I've been using a TI CC2540 device previously and there was...
Hi
is there a function with which I can check if indication or notification on a characteristic with notify or indicate capabilities has been enabled by the master?
Is there an internal counter for the number of packets transmitted since power on?
Im trying to change the advertising packet content after a timer is expired or a certain...
Hi,
I am using example bootloader from Nordic.
SD7.0
SDK6.1
S110
2nd rev chip 51822
IROM 0x3C000 Size 0x4000
Optimization Level3
The implementation is based...
Some months ago, I was told that a new BLE DFU Bootloader with code signing/encryption was expected before July.
Can we get an update on the expected release day?
I find "led_radio_example" and "button_radio_example" as 2.4G transceiver with nRF51822.
Is there any example source code about how nRF24L01 can talk with nRF51422?
Hello,
I'm modyfiyng a NUS template. I noticed, that when I move to far with my Android phone (with the nRF UART v2.0 app) from the NRF51 PCA10000 board, it disconnects...
The above mentioned example ( here ) is the one that is available in GitHub.
I want to implement bonding with static passkey based on SD110 v8 and nRF51822 with Device Manager...
I've tried to drop in all non-main code from the spi 5W example into my program and I keep getting the following errors:
.\_build\nrf51422_xxac_s110.axf: Error: L6218E...
Hi -
Looking for a layout review of the NRF51822 antenna and oscillator design attached. The two main questions are:
Is it recommended to remove the copper ground...
Hi,
any plans to release firmware package for nrf51822 smart beacon using Soft device 8 and SDK 8? Thinking I better ask before I start adapting it on my own.
thanks...
What is the pinout on the DEBUG OUT-pins?
How do I adapt the code to work both with dev board and an external chip?
There are BSP stuff I probably can't use that I use for...
I am using S110 7.1.0 which I know has the ability to unblock the CPU during Radio Event. However I would like to do the opposite and increase the time between a Radio event...
