I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
I'm using nRF51822 SoC and i want to notify the Androïd(4.3) application with the changes of the Major value due to switching the beacon mode . How to change Major value ...
Hi,
i can say that i'm familiarized with nrf51 devices from some time ago.
Using softdevice 7.1.0 and MCP 3.7.1 i was able to perform a device firmware upgrade using just...
Hey I am working on nordic nRF51822, I have a doubt.
Basically I want to use it as an iBeacon and along the iBeacon payload I also want to send some services.
Is that fundamentally...
Hello,
I tried to get the bootloader dfu example with the S110 8.0 and the latest 8.0.0 SDK running but ran into tons of issues. The packet handling with KEIL is just insane...
Hello everyone!
I'm writing here becouse I'm quite new to the embedded world and I'm experiencing some troubles starting with this platform.. I must say that, since I found...
Hello,
In my application, I'm going to power the custom board with a fixed 5V connection. What is the best practice for powering the nRF51422 IC? I was thinking in using...
Hi.
We need to ring the Buzzer with 4.2kHZ PWM.
However, in the event of 4.2kHZ in nRF51822 PWM is inaccurate about 2us.
Please tell us how to fix it.
※link Very...
I use this step-by-step guide to run nrf51 Iot SDK example on nRF51822.
First I modified app_ipv6_coap_client_pca10028 such that I can run it on nRF51822.
I downloaded...
Hello Everyone,
Im using the NRF8001 for my application and was looking through the arduino SDK provided by nordic.
I want to run the device in UART mode but do not...
Hello!
I have been trying to figure out how to get the device ID/MAC address for the NRF8001, and I found the lib_aci function lib_aci_get_address() that calls a cmd event...
Hello!
I am using the nRF8001 BLE chip on the Redbear Labs Blend board, and I need to get the MAC address, which I heard is also called the device ID. I understand that...
Hi,
I am new to BLE development and I am currently using nRF51822 with the soft device S110. I am using the example ble_app_hrs that includes the ADC converter. I would like...
Hello,
The max TX power for nRF51822 is +4dBm and it corresponds to Bluetooth Class 2.
Is there a possibility to use an external amplifier to increase TX power to meet...
Hello,
I'm trying examples supplied with SDK, running on pca10006 with nRF51422 chip board and Segger J-Link debugger.
I am able to
Erase entire chip with nRFgo...
