Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
Hi,
There is a following initialization in 51822:
static void controls_init(void){
uint32_t err_code;
// Configure pins.
uint32_t pins_transition_mask = (1 << SCKIN_PIN...
I'm working on a project using the nRF51822 beacon kit (PCA20006), and I've downloaded the firmware files installer from the website. After running the installer, I can see...
Hello,
I have a ptr5518 module which has nRF51822 in it. I need help programming the device. I am new here so a detailed help will be very useful.
I want to use the built...
Hi,
I'm workin with nRF51822 as peripheral device. is it possible to retrieve the device name of the central at the moment of the conection i mean when is generated the BLE_GAP_EVT_CONNECTED...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
When the line wrtHandle = hdr->Handle; executes I get an Hardfault Error. Why?
case BLE_GATTS_EVT_WRITE...
Hiii, i work on PCA10028 nrf dev kit and i want to made code that receive data from mobile to UC and go back to mobile. is anybody have this code than please give me and also...
Hello!
Looking around and reading a bunch of posts, I found little information on how to initialize the TWI sw frequency, which currently is 100 kHz( calculated it with...
I want to operate
Tries to operate a small speaker.
www.wvshare.com/.../Analog-Test-Board.htm
but I can not find the DAC function in nrf51822.
How do I create...
Hello,
I am starting a project related with BLE communications. In the future, I want to design my own board and to be able to program it. I am going to start with a development...
Hi, all.
I have been using the nRF51822 board, I am making a peripheral.
The peripheral has been equipped with a sensor to multiple GPIO.
(For example, sensor1 to P0...
Hi
I am implementing my custom service, and started from the led/button example.
I am using the LightBlue app on my iphone to connect to my device under test.
I can see...
I am trying to generate the services.h file and get an error that "Something was wrong with the advertising packet". I see at the end of the log it says "Return code: 0x2...
Hello All,
I have a basic question about empty scan response operation with the ADV_IND PDU. When I set advertising data as follows:
err_code = ble_advdata_set(&advdata...
