I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Trying to follow
devzone.nordicsemi.com/.../
but whatever I do, I am unable to make Eclipse discover the include paths or the source file paths from the makefile. I've...
Hi,
My Nordic kit just stopped detecting from last two days.
I have also check this in other PC also.
It detects some times some times not.
I am using Windows 8.
I...
Hi all,
I would like to know if it is possible to use the uart before the actual bootloader runs... I need to communicate with the master uploading the firmware before...
Hi All,
I need to implement a kinda a mesh network of Nordic device nodes placed nearby to act as a relay, for that I have a use case where following requirement.
...
I'm porting a nrf51 project to nrf52. I'm using softdevice s132 1.0.0.3 alpha. When compiling I get a lot of L6406E errors and a L6407E error. Do you know what's causing this...
hi,
I should how to transplant the official DMP mpu6050 library to nrf51822 above?I don't know how to transplant it and could you tell me how to transplant it?
I have combined to programs Ble_uart and Spi_Master into one. However, after uploading the file the GPIOs do not work (No clock is generated). Meanwhile when I erase the softdevice...
hi,
I downloaded the master control panel(mastercontrolpanel.3.4.0.8098.x64) from Nordic website, but it can't install it in my PC becuse of my 32 bit windows XP system ...
Hi,
Here is the piece of code that is bugging me.
The code algo is at every 500ms timer2 interrupts, and the adc captures 1500 samples and stores it in an array .I always...
I'm using nRF 51822 to develop a proprietary wireless protocol.
At Rx side, every 500ms have a listening window with 10ms to listen if there is package to receive. So 10ms...
I am testing with SDK6.1 S110 7.1. I've noticed that when I try and update the Bootloader image using the Android MCP app, everything updates fine. I have logic in place that...
Hello fellow developers,
I am new to BLE applications and I am trying to do a very simple device with three buttons that informs a Android smartphone when one has been...
Hello all,
I have an ANT project which is running fine using S210 SoftDevice (SDK v8.1.0).
Now, I am trying to extend this project for BLE operation, by switching the...
I have my devices programmed in a way, that they decide whether to enable SD and transmit via BLE or to keep it disabled and start operating using Gazell.
In this case I...
