Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Good afternoon,
I'm trying to test PCA10001 eval board power consumption and consumption is about 4mA when it should be considerably lower.
To proceed with this measurement...
Hello !
When i was trying to configur my SPI, I observed that there is a difference between the position field announced in the nrf51 reference manual v2.1 and the nRF51_bitfields...
We are looking for the sample software for transmission of nRF2726 (nRF24Lu1P).
nRF2726 does not carry out transmitting operation in enhanced_shockburst_ptx_nrf24lu1p.uvproj...
What I've been observing here is a curious issue under some very specific circumstances. First off, I am using a Xuntong Tech PTR9018 module (this is QFAAC0), the S120 1.0...
Hello all
I making some device with ARM core CPU with nRF51822.
I set CPU to SPI master and set nRF51822 to slave.
And then I read some data from nRF51822, that was...
I am Merging 3 firmware s110_nrf51822_7.0.0_softdevice.hex, ble_app_beacon.hex and bootloader.hex to Output1.hex as follows.
mergehex -m s110_nrf51822_7.0.0_softdevice...
I'm trying to use the Bond ACI command on my nRF8001, but I'm having trouble using it as per the datasheet.
When I set the Timeout parameter to more than 30 (0x001E), the...
The documentation for the nRF51 says only code from code region 0 can execute the erase and write command on code inside code region 0. This means that my bootloader in code...
I flashed S110 softdevice and ble_app_hrs application to nRF51822 on PCA10005 with nRF6310.
and then I tested by nRF toolbox on iPhone5s.
But ble_app_hrs application seems...
I'm attempting to implement a buffer in flash using the persistent storage module but have hit a bit of a wall. When I manually set the block size to something less than the...
Hi,
i'm developing an app for Android and iOS that needs to comunicate with a devices based on nRF51422 with S110 v7 loaded.
We want to encrpyt all comunication and enstablish...
Hello All,
I would like to implement static pin on my sensor. Remember how some Bluetooth Headsets are hardcoded to '0000' I would like to implement '123456' since BLE...
Hello all,
I am using nRFgo motherboard(nRF6310) and nRF51422 DK(s310) and
MDK_ARM(keil Version 5 IDE) to build the sample code.
It seems workable to program and download...
I just got an mBed board and I'm having trouble getting the J-Link to work on OS X even though I have version 4.90.
MattBookPro:gcc mbrandt$ JLinkExe
SEGGER J-Link...
Hi,
I have two types of nRF24 equipped devices, let's call it a BaseStation and a Slave. BaseStation is configured as PTX, whereas Slave is configured as PRX. Both use...
