Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi all,
I am new to hardware design and would greatly appreciate pointers. We intend to use mini-USB port for charging/power supply rather than for data. What is the best...
Hi all,
I am using NRF24LE1 32pin.
Does anybody know can I apply on XC1 pin external frequency different from 16MHz if I am not using radio module??? Thanks.
I am currently using the nRF51422 DK along with the nRFgo Starter Kit. I followed the instructions in the PDF "nRF51422_DK_UG_v2.0," and I attached the nRF51422 with PCB antenna...
use keil to download code to flash fail
use nRFgo studio to connect target device error
Load
C:\Keil\ARM\Device\Nordic\nrf51822_v5.0.0.34603_Backup\Board\pca10001...
Hello,
when using Keil's ULINK Pro debugger V1.57 connected to PCA10006 board for debugging nRF51822 code the ULINK is recognized by µVision V5.1.0.0 but the FW download...
I have an nRF51822 (256KB) that I want to program with some data targeted at 0x20000 to just under 0x38000. My code starts at 0x16000 (allowing for S110) and is only 1700...
I have a nrfgo 6310 start kit that I use for my nrf51822, but I'm wondering if I can also use the nrfgo 6310 for the nrf24Lu1 development kit as well? I tried plugging in...
Hi All,
I am working on the S120 bootloader.
I start it with dfu sample on nrf6310 folder. It work with S110 softdevice with PCA10001 perfectly.
I had made following...
Hi,
I would be grateful if someone could guide me a bit.
As far as I understand, nRF24L01+ implements Enhanced Shockburst technology in chip. To use nRF8001 as drop in replacement...
Hi all,
I am using s110 v7 for scanning and advertising, it works well. Now, I would like to measure RSSI while scanning (already scanned device but not connected) . Can...
Hi,
I am using nRF5182. Kiel is the IDE. I need to operate the device in 25Mhz. How can i change the clock frequency to 25Mhz. Is it possible? Will it affect the operation...
Hi,
I just stumbled upon the nAn-36 note ( www.nordicsemi.com/.../80193304 ) and I have two comments about it :
I think it's the best technical documentation I've...
Where to find definition for INTENSET/CLR for TIMERs in 'nRF51_Reference_manual v1.1'? I think I've read it all by now, but still can't find it.
After some digging I found...
If I have the PC insert 1msec byte spacing between data bytes sent to the NRF51422, it receives the message and doesn't reset. I can send messages less than 10 bytes to the...
my code shows here: github.com/.../main.c
uart_init();
printf("\r\n\r\n");
printf("\r\n __DEBUGGING__\r\n");
every time my app started, it always shows corrupted...
