Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hello,
I was reading about RF design and some articles say that if the transmission line is short enough, you may not consider impedance-control as the effect is not visible...
Hi all,
For my project I power the nRF51 DK from a supercap using an external LDO(3.3V) connected to VDD. This way I can keep the board powered using the supercap. I also...
Hi
I'm using PCA10028. it has nrf51422 with softdevice s110. For getting printf in console I'm using 'app_uart.c with FIFO' and 'retarget.c'. When i try to print something...
I'm developing a project base on ble_app_uart now.
But I find out that the current value of ble_app_uart is > 1mA.
I want to reduce the average value to about 10uA when...
Hey,
I have a requirement to launch google play store/ installed app in an Android/ IOS mobile upon pairing of the nrf51822 with a mobile.
So can anyone help me out...
Hi,
i'm testing softdevice s130 central/peripheral example. I modefied the uuid of device to which my nrf58122 should connect, but i get error 0x05 (Device not found) everytime...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I use sdk 5.2.0 now. And my keil version is uvision4(4.70.0.0). My PC is windows XP.
Now I want to migrate to nRF51_SDK_8.1.0_b6ed55f_packs. But when I run "install.bat"...
I am getting notification of connections established between two boards in hyper terminal. Now i want to send this notification on web server as it is part of my project....
When I'm trying to connect to the new nrf51 dk kit with nrfgo studio, and at the same time have another j-link based dev-kit connected to the PC, the studio hangs while trying...
I started with the ble_app_template example. This example uses the Button event and notifies it. I modified the project to send some other data as notification, instead of...
Hi,
I am using the following calculations to calculate the power consumption for the chip:
Formulae to calculate battery power consumption:
Current consumption is...
Hi NORDIC
I neen to implement a function that multilink central (S120) can receive information from multilink peripheral . I do not know how to implement it in software...
Ok so I've followed the instructions to make my dev dongle (pca10000) a sniffer in "nRF Sniffer User Guide v1.2". Now I want to use it the way I used to use it in MCP.
...
