Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am trying the ble_app_gls example of nRF SDK v16.0 on nRF52 DK device. The only modification is change s132 to s112.
After download the app to nRF52 device, I can successfully...
So what I want to ask is what is the scan latency during high accuracy and low accuracy?
Also if an insight regarding power consumption can be given would be great (we are...
Hi Everyone,
My Environment: nRF52840, SDK15.3, Keil
I'm developing a central / peripheral device that can automatically connect up to three peripherals.
I want to know...
I tried to merge ble and calendar example but when i call "nrf_cal_init();" I've got error "app: SOFTDEVICE: INVALID MEMORY ACCESS" i tried to use RTC2 in Calendar.h but nothing...
Hello guys,
I was working these days with nRF9160-DK board without any problem. Was able to update the firmware on it, to use it as a programmer for Thingy:91 etc...
I...
Hi!
SDK 16.0
I use secure bootloader from SDK with button.
1. Single app written from Segger Studio work fine.
2. Firmware (bootloader with app) written from script...
I'm located in Denmark close to Roskilde (Greater Copenhagen).
According to TDC (Biggest national operator) they have not opened for roaming yet, using the NB-IoT & LTE...
Hi Nordic Team,
In my BLE project I am trying to change the GAP parameters like
gap_connection_param.min_conn_interval = MIN_CONN_INTERVAL; gap_connection_param.max_conn_interval...
We were evaluating nRF9160 for IoT project. Wanted to know more about NB IoT
1: Does NB IoT support both 4G and 5G?
2: I have the following understanding , please correct...
Hello, I am trying to test out an ADXL362 module with my nRF52840 DK. It uses SPI to communicate. I have tried different speeds from 1M to 125K but nothing seems to work....
I have downloaded many things from many places. Even some by accident. I cannot figure out how to download nrfgo studio from the web site. Please help me understand this new...
Dear sir,
I am new to nRF52840 IC. We have selected two part number for 32.768KHz crystal. 1) ECS-.327-7-34B-TR( www.digikey.in/.../1850390) 2) ABS07-32.768KHZ-T( www.digikey...
Hello ...
Our product uses a secure bootloader based on the SDK 15.3.0 secure_bootloader dfu example. I've found a few posts eluding to bugs and would like to confirm whether...
I am trying to implement DFU for nrf51822 qfaa module I have used sdk secure boot-loader example. Its working on nrf51DK
but not working on nrf51822 qfaa module sdk : 12...
