Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi team,
I have to create a program which sends messages from one dongle to another. Now I have ported radio transmit and receive + USB CDC ACM programs for two 52840 dongles...
Hello,
I have experienced some softdevice hardfault in my multiprotocol application. I use https://github.com/NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver/wiki with...
Hello,
My application, running on nRF52840 with SDK15.2, needs to detect the reset source from System OFF state. However, when using the BLE Secure DFU Bootloader, it always...
Hello,
I use nRF5SDK160098a08e2 SDK version, on ubuntu 16.04.
I use pca10056 (nrf52840 dev-kit).
I want to run cc310 example located at ./examples/crypto/nrf_cc310...
hello,
We have a product in production using nRF51422 and we are scaling up volume in a new manufacturing facility.
The functional tester stations require use of Master...
Hi!
Is there an example of how to use BLE_GAP_CONN_SEC_SET_MODE_LESC_WITH_MITM?
I cannot find one and I am having a hard time understanding what I need to do to make...
Hi,
I'm trying to use the pc-ble-driver "nrf-ble-driver-4.1.1-win_x86_32" to communicate with our nRF52-based embedded product. The fact that the PC and embedded implementations...
Hi,
I am using NRF52832 with secure bootloader to OTA my application in the field using Dual Bank updates and everything is working fine. In my application, I am using FDS...
Hi,
I need to use external eeprom memory AT24C256. I have not found any example for nrf52, so I started with migration existing arduino code to Nordic´s. Here is the Arduino...
Hey,
I am working on NRF51822, S130 softdevice integrating security, I have used the GLS as a reference for security implementation.
I have a use case in which I am...
I have both ble_app_uart_c and ble_app_uart they are automatically connected to each other if they are on. my question is ble_app_uart_c supports one to many or not? if it...
I am developing using pc-ble-driver-js and nrf52840 dongle.
We know that nrf's development tools (nrf connect ...) are being developed using an electron framework,
and...
We are using SDK 15.2.0 and softdevice s132 v6.10. we want to use the concurrent feature for broadcaster and observer. we wanted to just confirm that this feature is reliable...
Hi, I don't understand enough about electrical, but i found that a little piece of component in my nRF52840 dongle was gone.
It was something in this position:
It was...
Hello,
I'm trying to measure execution time of a piece of code in nRF52832. I was searching and found that I need to get the start time and finish time by using
beginval...
