Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
1. I am trying to implement DFU(with USB&BLE) and USB Mass Storage with FAT FS filesystems on external QSPI flash. I am getting the following build errors- with SDK version...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Dear Nordic
I am programming with nrf52833,ncs v2.9.0 base on sample\peripheral_hid_keyboards
Peripheral side(nrf 52833) adverting as Scanner_CE42,and iphone connect to...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
Hi,
Due to pcb constrain, we need to use single button mode with PG/RESET routed to SHPHLD. In this mode long press for reset in the datasheet but nothing is said about...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
hi everyone.
we are migrating to nordic nrf51 series (before we used ble modules from another vendor blugiga which depends on cc2541 chip) so I m pretty new at nordic nrf51...
Hi all,
I'm using the pca10031 which contains the nRF51422 chip; as a packet sniffer to sniff the communication between my S5 samsung and my pca10028, but I struggle while...
Hi, I'm trying to use the example bootloader with the new NRF52, everything seems to work fine except that I'm unable to bond to the device when the bootloader is installed...
I sniffer the packets when I use a phone to connect to a BLE device.
However, in the packet with CONNECT_REQ label, the source address (init address) is not the bluetooth...
Hi.
I'm trying to communicate with legacy nRF24L01P using nrf51822.
I received packet from nrf24l01p, but I can't send information back.
The data I should send is more...
I use the persistent storage manager for saving some calibration parameters. It seems to work ok - I can power off/on, and the values are still there.
However, after I...
Hi. I would like to get into bare metal programming, and have decided to go for ARM processors. Are there any ns-kits or courses availible for purchase?
thnx in advance...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
Dear All,
I'm trying to set a static passkey. I have created 2 custom characterestic. One characterestic is used for notifications and the other one for writing. For communication...
I'm making a peripheral device that should be powered off most of the time, but never idle if on, so I want to make sure that it is always (1) connected, or (2) advertising...
