Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello,
I am need to add voltage sampling functionality to existing FreeRTOS framework on a low-power BLE device. When I enable BLE, I get 3mA of current, which stays there...
Hi,
When I call sd_ble_gap_disconnect( m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION), it usually takes about 100 msec, and come back with event BLE_GAP_EVT_DISCONNECTED...
When not using the SWD port I would like to pull up the SWDIO and SWDCLK lines high. Does the NRF52810 have internal pull up on these two pins? If not, what value pull-ups...
Hi,
I have received nRF52840 development kit recently and I am trying to work with Proximity demo application on my mobile phone. The problem is no device is shown on the...
My Project involves adding BLUETOOTH mesh to a current product.
In that product we use the Flash Data storage library to read and write flash. The SDK for mesh documentation...
Hi ,
I tried to download nRF Command Line Tools for linux 64 bit from your server today (01.22.2020). Even though I chose linux 64bit operating system, clicking on link...
Hi,
I bought an nrf51822 beacon from ebay, it has an LED and a button. I am trying to figure out what pins the LED and the button are connected to, without much success...
Hi,
I have cloned code from https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo and everything was looking great.
I have built and loaded code to my 2...
Hello,
on nrf52832, sdk16 S132, I'm using timer 4 and Compare system to step forward in a PWM sequence. everything is going very well until I have more than 3 PPI Chanels...
Hello,
I am using BLE peripheral. I want to send more than 200 bytes of data to the mobile phone. What I need to do in the characteristic definition and after that.
...
Hi .. i am new to pwm, i want to drive the gear motor for that i need pwm pin , which pin i can configure , how to do ? how to configure the pwm pin . which example will be...
Suppose node L is in a friendship with node F. Consider the following:
1. Some other node C sends a message to L.
2. F hears the message, and saves the message into...
Hi Nordic Team, Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support and Example code?
Hello. I 've analyzed a couple of topics here regarding to poweroff. But still want to clarify something. In my project I need to keep MCU in lowest possible power mode, but...
