Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Is anybody have any experience powering nrf24l01 with smps stepdown converter?..i have trouble using fr9702 as 3.3 volt supply for nrf..the problem is..nr24L01 cant received...
Hello,
I have a question about the NFC tag. In the example nrf_url_record_pca10040 there is a part where the url will be written in the tag
err_code = nfc_uri_msg_encode...
I develop ANCS success in S110,but in example ble_app_hrs_rscs_relay of S130 SDK9 .I don't know how to add the ANCS.I find S110 has ble_bondmnngr.c file,but in S130 dosn't...
quick-stop_2_with_soft_filter_NRF52_DK (1).hex I imagine that my question is just one from lack of experience. I apologize for that but I cannot find any information on the...
Hi!
I would like to use long button press to send device into sleep mode (using BSP module). Since button is tied to ground, when device goes to sleep mode, and when I...
I need to us an external RF amplifier that requires TX and RX control lines. I'm looking for a way to tell when TX starts to kick the unit into TX mode. I also need to know...
Hi,
We use NRF52832-based BLE module running serialization (SDK 14, softdevice 5.0.0) and STM32F407 MCU running application firmware on a custom board. The project is created...
Hello!
I am looking examples for nRF5_SDK_14.1.0 (For example - ble_app_eddystone )
I need read all attributes with ATT_Read_Blob_Req command.
I can read Device Name (0x2A00...
Hello,
I am using nrf 52832 and sdk 14.0.0. and i am using "ble_app_uart".
I am developing an iOS application.
Its purpose is character transfer.
I want to transfer...
Hello,
I did a quick test using 2 nRF52840 kits to measure the change of the RSSI value based on the distance and the used PHY layer.
For each test, I configured both...
I was reading through the documentation and it mentions you need;
One PCA10028 or PCA10040 development board for the client.
Three development boards or dongles...
Hi,
Is anyone successfully using MMD with the nRF52840 PVK, SES 3.3, recent SDK (e.g., 14.1.0) and S140 softdevice?
I followed the steps in this blog post both on Win10x64...
Hi.
Our company is designing a new device using the nrf52832 chip for BLE communication with other equipment from our Company.
Does the chip come with a factory preprogrammed...
Hi
We are developing ble peripheral application for the nrf52832 using SDK v13.0.0. and everything was working correctly until we tried ble connection with the iphone 7...
Hello Sir,
I have developed my application using nRF52832 chip with BLE connectivity. My device is battery operated and hence i am looking for WiFi chip with small size...
