Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
My application uses SDK 11 and s130 on an nRF51822. In certain cases I want to delete all my bonds and go into sys off.
I presume that when I call pm_peers_delete() , that...
I am not clear on what is failing to open here. Anybody have any tips.
(This is on windows)
C:\projects\CB\app>nrfutil dfu ble -f -pkg _build/careband.zip -n test
Please...
Hi Nordic,
I am trying now to create a star network, in which the central node is master of different slave channels. The idea is to configure and open different independent...
Hello,
I'm using the ble_app_uart_c as an example for a Central application. After writing to a characteristic in a peripheral I expect a notification back from that node...
I have a main loop in my application like this:
while (true)
{
// Other calls left out here.
app_sched_execute();
err_code = sd_app_evt_wait();
APP_ERROR_CHECK...
Hello,
I am new to the nordic's controller. We are planning to evaluate the nRF51/52 for our IOT application need.
I am more interested to know the possibility to have...
Hi,
I'm using the button event handler code on the SDK. It fires once when pressed down, and once again when i release the button. How do i make it only fire once per push...
I have two nrf51822AC mcu chips that are integrated on custom boards, and I need to communicate between those two chips (one set as a transmitter and the other as the receiver...
Hi,
I own company that builds a PIC 8-bit devices, and can code at a low bit level in the PIC environment.
I picked up the NRF52 Dev board, and am trying to learn the...
My peripheral device connects with central one very rarely. I decided that I don't want peripheral to negotiate connection parameters with central, just use settings imposed...
I'm developing custom board of nrF51822 CEAA (256k, 16k)
I set my bootloader ROM, RAM just like below
as I understand,
Firmware size should not larger than...
hi,
i just ask about nrf52832.
im using it with keil compiler and trying to divide the memory section (it that will be update and not)
but i have hard time to do with keil...
I'd like to log some debug stuff to a mobile app over BLE, when in a connection, using the NRF_LOG library and the Nordic UART service. I have this working just fine without...
I'm trying to write to specific address on flash memory (data region) for debug purpose using
nrfjprog.exe --memwr 0x3B820 --val 0xAA000000 --verify
but when I read...
