Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I'm using the nRF51822 and pCA10001 as SPI slave.
For reasons beyond my control I have to read the Rx Buffer before the CSN is released.
Yes, I know I shouldn´t do...
Hi!
Could I find somewhere (I was trying in Nordic docs and in previous posts but everything refers to previous versions of softdevice) how to perform bonding with key...
Hello,
When designing a 4 layer board with the nRF51822, should I connect the chip and impedance matching circuit to analog ground and keep the other digital chips isolated...
use nRF51822_Evaluation_Kit
I want to auto bonding by peripheral ,once peripheral connected with center(android app).
Is there have any API to send pairing request?
Hi, I tried uploading the example code from \nrf6310\spi_master_example to nRF51822 evaluation kit board, but no matter what I do, I always get SPI error. Not compile or upload...
Hi,
is there a nRF Master Control Panel equivalent App for iphone?
I'd need an app where I can set custom characteristic. The background is to update the device using...
I'm a begginer in embedded program. I have a mbed HRM 1017 that
is pin-compatible with Nordic PCA10004. .
I'd like to make a simple app to print out "Hello World" to terminal...
Hi guys,
How to update softdevice on mBED nRF51882 kit?
Details:
I have couple mbed dev kits with nrf51882.
I use Keil for development but will move to GCC after while...
Hello all,
I wanted to ask if there are any cad files for Eagle or other hobbyist level design tools for the nRF51 chips before I spend time to create and debug them? ...
hi guys,
I'm pretty new to nordic ble development, but I have a fair idea of the differences between EK, DK and the mbed enabled MKIT.
I'm trying to build a deploy about...
I have been following this post and pure-gcc to set up my eclipse environment in ubuntu 14.04. Thus far everything works well except i cant figure out why the softdevice is...
Hi,
I made own board based on the dev kit board with PCB antenna.
I flash SD110 6.0.0 and then I load bluetooth_hrm demo and there are no errors, but I dont see Bluetooth...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
The mbed IDE was recently updated to support S110 v7.0. I'd like to use the Timeslot API to program for my nRF51822 mkit boards.
Has anyone been able to get this to work...
