Dear Nordic Engineers
The following documents are our hardware designs. When we conducted the test, we found that we couldn't obtain the GPS satellite signal and the 4G...
I’m using the Zephyr nordic,npm1300-charger driver on an nRF52840 to control the nPM1300 PMIC charger. At runtime I need to be able to turn charging on and off—on command...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi, I would like to ask that, whenever I put my function in main.c, the borad become undiscoverable.
I'm using nRF51 with ble_app_uart_s110_pca10028, and below are my function...
use nRF Toolbox APP to bonded peripheral device even disconnect and connect don't need input PIN code again, but when I turn off BT the APP lost bond information. next time...
Can the S120 work without RTC XTAL?
Iam using SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, false);
but it still hangs in the softdevice_handler_init...
Hello,
I am attempting to implement the TWI drivers from the SDK for a nrf52832 chip for a pca10040 board. I am using the twi_hw_master files to drive my TWI and insofar...
Hello.
Since i migrated from 1 to 2 SPI bus, IRQ Handler at completion is not called. Can I use 2 easy DMA SPI ?
1 bus was working fine.
here is my config
/* SPI...
Hello Nordevzone:
8.0 multilink example
I tried to use this modified handler to receive notification data from a s110 based application. The centerpiece of the handler...
Hello! I have been playing with this example and got some LEDs blink here and there, but would very much like to have UART working as well. The documentation states that ...
Hi,
I'm using the nRF51822 for a beacon and following the ble_app_beacon example (SDK 8.0.0) with some modification in order to measure the battery level through the ADC...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Hi,
I have some questions regarding connecting multiple (as many as possible) BLE peripheral devices to a single central (simultaneously).
1:
Does anyone know of any...
Hi
I now is developing Android apps on the basis of NRF UART v2.0.
My s110 NRF51 device will switch two modes for differnet 128-bit UUID. These two modes have independent...
The Bluetooth 4.2 specifications allow for an L2CAP MTU size of up to 255 bytes. It looks like the CC2640 already supports the maximum MTU size of 255 bytes with a 248-byte...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
