Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Hi Nordic team,
We're experiencing two issues related to partition handling in Zephyr/NCS and are looking for your guidance
Issue 1: settings_storage is erased after BLE...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
8.0, multilink example, peripheral, s110 softdevice.
By walking through sections of codes and doing some research, I reckon if a connection were being established after...
I try to Development with GCC and Eclipse following tutorial
but i get some problem , which i can not solve alone.
so hopelly someone can help me to solve it ,thx!
that...
Hi，I use nRFgo Studio to erase nRF51822, like this
but it display: ERROR: Invalid serial number!
I found the question how to use nrfjprog --snr??? ，I can get the...
I am using the nrf24l01 on a FRDM k64f board, I want to communicate between the board and my laptop, so I have bought a nrf51 dongle.
I am using mbed on the k64f board...
I try to create a custom boot loader that enable to update soft device via data come in from SPI msg. When I try to use the command nrf_nvmc_page_erase() to erase the flash...
Hi everyone,
I'm a beginner in Android development and BLE environment, and I want to communicate with the nRF52 card using an Android app. In fact I have to develop an...
hi,
I am using the nRF51 with code from SDK 9, as well as the S110 softdevice and made a custom service(128-UUID) with bond using device manager.
connection and service...
Hi,everyone,
I would like to know that what's the dedicated bonding ?
I saw this in the introduction of a BT chip.
I am confused with 'dedicated bonding'.
And what's...
Hi,
I am using the nRF52 with code from SDK 9.2, as well as the S132 softdevice. I basically ported code from the ble_uart_app into the twi_example to send data over bluetooth...
In the very first blinky example from the nRF52_SDK_0.9.1:
#include "stdint.h"
#include "stdint.h"
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards...
hello,my experiment phenomenon is:one nRF24L01's channel is 0x0A,used as send terminal；the other one nRF24L01's channel is 0x02，used as receive terminal；receive terminal can...
I try to make a build of the example ble_app_hrs_rscs_replay_pca10028 (central and peripheral experimental) in SDK 10. My MCU is nRF51822-CFAC, and I'm using IAR compiler...
I'm using custom board with 32MHz oscillator and S110 SD 7.1 (SDK 6.1).
Somteimes (quite rare) the chip completely hangs when calling sd_flash_erase in pstorage.c.
Only...
hello
we use nRF51822 QF AC A1 / IC rev 3 with SDK 6.1.0 / S110 7.1.0. We have produced and delivered to client > 1k units
pwm code nrf_pwm_noglitch 02.2015 from
github...
