Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hello,
I'm curious about how to deploy my application to multiple nRF51 Dongles at the same time while I am developing. I have the same application / hex file running on...
Hi,
I'm trying to connect my nRF51822 PCA100001 development board to a ARM M3 processor via the SPI. In this case the ARM M3 is the SPI master and the nRF51822 is the SPI...
Hi,
I am having a nRF51 DK(PCA10028) development kit. I am trying to run blinky example on this development kit using Eclipse+GCC environment. I am following nAN-29 application...
Hi, I'm trying to locate the Softdevice whitepaper (nWP-20), the S210 softdevice specification makes reference to it, but I can't seem to locate it anywhere on the nordic...
Hello Everyone ,
I want to use pstorage for my project.i get the example code from here
devzone.nordicsemi.com/.../
and its working properly(i.e read and write operation...
I am using nrf51822, after establishing connection between master and slave, circuit needs only tx antenna, is there any way to put rx in sleep mode for ble application? During...
I have some nRF51822 MBED kits and I want to use them for BLE for both peripheral and central roles. I understand that this is possible with the S130 SD and the Nordic SDK...
Hi, this question could be ridiculous question due to my lack of data structure knowledge.
As you see in the HID keyboard example (SDK 7.2), there are several buffers....
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
It took a bit to learn these offsets and configure the keil project for them. Do these need to change now that I want to begin using the OTA bootloader? I'm imagining that...
It's probably a rare bug, but it is still worth noting. I have been debugging this issue for a day.
I am using SDK 6.1 at the moment.
The problem was that Device manager...
Hello everyone, right now i make my own nrf51822 kit. it works good for all sample example when i use minimum current consumption example it shows 4.5uA current, then i erase...
I would like to create a sensor network consisting of up to 17 nodes, I've been collecting a lot of information about means of communication between them and a computer and...
Hi All,
From the data sheet nrf51822 have a aes hw modules which is used bt softdevice s110.
If i disable the pairing key .
Can I use the inbuilt aes module from...
I am using DEVICEID as an identifier (I know it's not necessarily unique) but when I break the two 32-bit numbers out into bytes, I am finding that the three most-significant...
