We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Can anyone tell me how to connect NRF 8001 with Arduino mega 2560. I have developed an iPhone application and just want to connect with NRF 8001.Please tell me how to connect...
OK, probably a dumb question:
The nRF51822 reference manual indicates that the RTC is driven by an external 32 KHz input. Can anyone confirm whether it will or will not?...
Hi
can you please help me convert these Keil pre processor calls to something that gcc compiler can . If possible i would like more information about these calls and the...
I'm using Nordic NRF51822 and the Segger JLink with the s110 Bluetooth stack active (correction: flashed on the chip, see below). When my code hard faults (say due to a dereferencing...
hi, I currently stuck in the follow section:
static void gpiote_event_handler(uint32_t pins_low_to_high, uint32_t pins_high_to_low)
{
if (pins_high_to_low & (1 << BUTTON_0...
Anyone to tell me where can i get the CDB file for nRF24LE01? I've downloaded the SDK and the nRF go Studio, but i still cannot find the CDB file.. Please help me to find...
Hello,
I'm trying to start softdevice on a custom board with nRF51822 chip and S110 device. The code hangs in SOFTDEVICE_HANDLER_INIT. It seems that EVENTS_LFCLKSTARTED...
Hello,
firstly I would like to say that I tried searching the forum for a post that has similar problems to my own. But I haven't (please tell me if i'm wrong) seen any...
Question: Can a nrf51822 acting as a server/slave message a client/master (iPad), that it has bonded with previously, to let it know that new data is available without having...
Hello,
I would like to experiment s120 on the evaluation board.
There are some examples but in nrf51/nrf51822/Board/nrf6310/s120/experimental.
Can I use it ? Or is there...
What are the correct PTX and PRX configuration settings for using dynamic payloads with auto ACK disabled? Can I just clear EN_AA and set EN_DPL and DYNPD for the pipe I'm...
Hello! I am working on a project in which I want to send stored sensor data to a smartphone whenever the phone is in range or at specific times of day.
Most of the communication...
Hi,
I am trying to get hold of version 2.1.0 of the dev kit for use with the sniffer. The dev kit is in stock at Mouser but they can't confirm the version number, but said...
I have developed the schematic of connecting NRF 8001 BLE chip with Arduino,the file is attached that contains the schematic. Can you please verify my schematic i.e will it...
