Hi Nordic team!
Is there any way to dynamically change the charging current while the charging is ongoing? BCHGISETMSB and BCHGISETLSB can be changed only if charging is...
Hi there,
I am currently trying to use device sleep modes with Matter. Nevertheless, once I add "CONFIG_PM_DEVICE_RUNTIME=y" to my prj.conf, the main-method is not longer...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hi,
I have a JLINK EDU and JLINK LITE and an nRF52 module and am attempting to use nrfjprog to program the device. Both devices are able to erase the chip, but the JLINK...
hi,
i'm new to bluetooth development so i have got a Tiny BLE. ( wiki.seeedstudio.com/.../Tiny_BLE)
the Chip is: nRF51822
i use for the development at the moment the...
Does Nordic, or any third party, provide an iOS app that utilizes the features of BLE 4.2? Specifically the larger packets sizes, and is there example code? Wish list would...
My net is a star type with many nrfL01P+ units.
Now i simply use only pipe 0 with no acknowledge (and same frequency for all units).
My question is if can I use pipe 1 ...
Hi,
I'm building a device with an nRF52 or nRF51 Module (still undecided), but still need a second MCU for USB Host functionality. Unfortunately, USB Host requires a precise...
I modified the nRF51 SDK_v5.1.0 .36092\Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs proj and downloaded to my self-made pcb,and it worked well. Then I want to update to...
Hi there,
I'm using an input GPIOTE based on SDK11. The interrupt is consistently being fired. On the other hand, if I use "if(Pin_6)" to check the trigger, it does not...
I am trying to use SEGGER_RTT_printf with SDK12 in eclipse.
I have added the appropriate lines to the makefile and SEGGER_RTT_WriteString works fine.
My Makefile lines...
I followed this blog entry ( devzone.nordicsemi.com/.../) setup IAR to debug in monitor mode (by adding Jlink_monitor.c, jlink_monitor.h, jlink_monitor_isa_iar.s, add EnableMonMode...
Hi,
In our project we need to store data onto the internal flash memory.
The data that's stored will be transferred and modified via "BLE uart service". When I tried...
Hi guys,
I'm working on an nRF52832 chip (PCA 10040) with softdevice s132 (v3.0.0) and I'm facing with a big problem; in my project I use an spi (instance index 0) and an...
Hi,
we have the need to develop an application that needs a precise second counter over time.
Our firmware is using the S110 SoftDevice (v8.0.0) and SDK v8.0.0 to perform...
Hi!,
I'm trying to compile GitHub examples, for example this github.com/.../nrf51-ble-tutorial-service
I cloned it into nRF5_SDK_12.1.0_0d23e2a/examples/peripheral....
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
