Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am having problem to download SDK NRF51 12.0 example firmware onto Redbearlab BLE Nano nrf51822. The compilation and build is fine. It is shown as
Erased Failed!
Error...
I have a custom board with an nRF51822, running the ble_app_hrs from the 12.1.0 SDK with softdevice s130, using the internal RC clock in a custom_board.h as follows:
#define...
I'm learning about the nRF52 series and so far love everything I see, especially the SDK. But I just got to the point where I'd like to generate precisely timed output, and...
Hello Nordic Team,
As I'm worrying about the max payload lengh that I can notify using soft device s130.1.0.0 on nrf51822 (256 Kb Flash/ 16KB RAM, SDK10), I thought about...
Hi,
I'm porting our project from sdk10 to sdk12 with SD S132 V3.0.0. I cannot find a way to reset the device in app and boot in bootloader in order to do a OTA update....
I have a working custom DFU bootloader based on the official bootloader from the SDK 8.1.0.
Updating the normal application code works without any problem.
Now I want to...
Hello all,
I try to trigger two events with two different periods, the first at 200ms, the second at 300ms. When I set the same period for the compared value, it works...
Hello,
I am tring to do a Bootloader update OTA using the bootlader DFU Dual Bank. Application update OTA is working fine while it is not the case for Bootloader update...
Hi,
I can't get my head around the cipher and auth used by SD132 in BLE (nrf52832,SDK12).
Could someone please explain which HW blocks and SW libs are used for encryption...
Hi, I'm trying to create a custom PCB that uses nRF52832-QFAA and a Meandered trace antenna.
The PCB's environments are 4 layered, FR4, 1.6mm thick, and green PSR ink....
Have built the HTS example and flashed to the PCA10040 board.
Using the iOS app HTM (within nRF Toolbox):
connect.
get notification from the Battery Service
...
Hello,
I have a low-level application that does bluetooth reading to find beacons, and I would like my application to read the battery level to display in my web application...
I have some keyword, want to save to UICR CUSTOMER registers.
Then, when I start he board, I can get the data from UICR CUSTOMER registers.
but, I donot know how to ?
...
