Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
I read that the DEVICEADDR is always in the advertising packet, so i need to take these data from the master each time that a slave is conected to them. I trying do something...
I'm using nRF52+SDK11.0.0+s132. In the ble_hrs PCA10040 example, the following are defined:
BLE_STACK_SUPPORT_REQD
BOARD_PCA10040
NRF52_PAN_12
NRF52_PAN_15
NRF52_PAN_20...
Similar to the thread posted here , I am trying to merge SD+bootloader+application and flash this to a nrf52 using the Segger programmer. This saves us a huge amount of time...
What is the best way to start a new nRF52 project, on a custom PCB?
I have a custom PCB, with nRF52 module. I use IAR, with ST-LINK V2
Say to test the GPIOs, do I start...
I took a look into the PCA10040 and the differences from PCA10036, seems to be minimal...
NFC connector and some breaking points. My question is: if somebody from Nordic...
Hi,
I am new to the nrf52. I want to implement the code that gives me current date and time value based on default set values.
for this i need to read the current counter...
Hi
Any ideas how best to implement a combined iBeacon and standard advertising device (both devices are active at the same time) ?
The iBeacon has to send an advertisement...
Is there a way to generate a DFU OTA image from OS X natively without having to use a Windows platform? It seems that the missing step is dat file generation and json manifest...
Hello guys,
Firstly, i would like to apologize if this post doesnt belong here. But i couldnt find any other platforms anywhere else for me to ask this question. So i have...
hi .
i did what this linke says
but it get me these error
..\main.c(632): error: #20: identifier "NRF_CLOCK_LFCLKSRC_RC_250_PPM_TEMP_8000MS_CALIBRATION" is undefined...
Hi,
I've got some really simple code I've been trying to get working with SPI on nRF52 (while also using SoftDevice):
///MISO, MOSI, SCK set, but SS not
err_code =...
I am trying to figure out if I need to disable the softdevice to get the power numbers in to the single-digit uA range.
With the softdevice loaded/enabled, but with the...
I'm developing nRF52832 to implement the Eddystone (※ 1).
But i'm thinking seriously about what can I do to have the Eddystone Specification and compatibility.
please...
I am working with the ble_app_buttonless_dfu example and am wondering why the example sends 2 notification messages in response to a command being written to it? This occurs...
