Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
How can I differentiate between a brown-out and an initial power-up on the nRF54L15? In my project, I need to detect a brown-out event in order to trigger specific actions...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Dear Nordic Engineers
The following documents are our hardware designs. When we conducted the test, we found that we couldn't obtain the GPS satellite signal and the 4G...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi there! I'm using the nRF Toolbox's UART to test the receiving of my data stream. I'm trying to send a data array collected (from spi) in my main loop and send it via UART...
I am studying the iot-sdk of nordic.
Now, as I have shown in previous questions, I can not detect the device under the linux system according to the toturial in iot.
Now...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1?
About problem:
...
Hi,
I've been trying to add the option for BLE HID to the Espruino JS interpreter on nRF52 - it's something that ideally would be switchable at runtime.
After having...
Dear All
In my application we could not use the ADC inside the nRF51822 because 10bit are under our requirements. But now with the new nRF52xxx with a built-in 12bit ADC...
Did anyone manage to build project on Eclipse with some nRF52 BLE application for HomeKit?
I have found only one project from aanon4 but I cannot even build it.
Sometimes...
Hello,
I am thinking of creating a project that I intend to manufacture that needs to operate 10 dc motors via Bluetooth.
Would this be a logical and cost effective...
I am using nrf51822, I have two firmwares with different offset address, one is having offset address of 0x16000 another at 0x28000.Both are 60kb of size each. I want to start...
Hello all,
I try to find out how long some configurations of the Enhanced Shock Burst protocol take time. I am working with the nRF52 Development Kits.
Some timings...
I want to combine two applications, both of them having two services. One application resides at 0x16000 and other one resides at 0x249f0. I am using softdevice 7.3 and sdk...
I am using nrf51822 and softdevice 7.3. I am working on the github mesh example. I want to add uart service with mesh, so that I can communicate with that particular device...
Hello, this is what I can think of when porting a project, but before that, a little background about my project:
it uses BLE (duh)
it uses uart to print test output...
Hello,
i am using the nRF52 Development Board with SDK 11 and I have trubble with the UARTE Interface with DMA. Parallel I have running the ESB protocol.
I know the problems...
hello there i want to add battery service and thermometer service in advertisement packet. so i changed in uart project. but in advertisement project i can see battery service...
hi
I used the nrf51 dongle to receive advertisement packet from other nrf51 dongle. I used this formule, d = 10 ^ ((TxPower - RSSI) / 20) , given from this link forums...
