Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi !
I just got my new boards with the NRF52 CPU.
When i burn the firmware that worked on the PCA10040 evk it works but on my hardware it resets immidiatly.
On my...
Is there a UART bootloader available for nRF52840? Doesn't have to be secure.
Already searched in SDK 12.2 and 13 alpha, with no success.
Thanks for your help!
I installed the latest JFlash (6.12d) from Segger's site, and it updated the JLink firmware.
However when I try to program the hex files downloaded from www.nordicsemi...
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL does not set the .burst field in the nrf_saadc_channel_config_t structure.
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE...
The app_fifo support e.g. in SDK 12.1.0, appears to have a serious problem when the read_pos/write_pos values wrap. i.e. when the fifo has been used over a period of time...
I have BLE400 extended board for nrf5. It has cp2102 on board from Silicon Labs. I installed drivers for mac and can see NRF_LOG_INFO via terminal. It would be great to have...
i am using nrf52840 with sdk 13.0.0-1.alpha. I want to boot the application from bootloader but by
using UART as a transport layer.
Would you plz help me?
I found end of address of fstorage from macro of "#define FS_PAGE_END_ADDR (fs_flash_page_end_addr())". But I want to change the start address of fstorage. Which macro or...
I have multiple GPIOs that are configured to use GPIOTE in my application. When one of these GPIOs is in the active state I start timer. Once the timer expires I want to enter...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to work with VL53l0x distance sensor. Basic communication working good, but i am not able to get distance...
Hello
I tested a BMD-300 Module and Nordic Team has been very helpful.
I tried to reach the maximum speed in this module.
I like to send 4x20 byte per 30 ms, but I...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
