Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I'm reading the SDK 10's GPIOTE doc and I'm wondering if there is a way to read a GPIO state without generating an event, ie, something like foo = PORTx.pin10 or alike.
...
Hi,
I have a central that is trying to pair with a peripheral. I want this connection to be secure and I want to use ECB for encryption of data. My peripheral does not have...
Hi,
I'm trying to communicate the nrf52832 with a LIS2DH accelerometer and when I'm trying to read 192 (32*6) bytes of data (to empty the entire accelerometer's FIFO) my...
Hi,
I want to know what is my execution time for each function.
I am using nrf51822 chip and the IDE is IAR Embedded Workbench.
How can i calculate the execution time...
Can I detect overflow on RTC1 when using timers with S130?
In my App, I use timers but also count time with NRF_RTC1->COUNTER. I need to know If overflow happens.
It seems...
Is it right that this flag BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED , prevent my device to be discovered by classic Bluetooth stacks?
Which of these flags do I need to use...
Dear Nordic experts,
After experiencing a lot of random issues when retaining bond information during a DFU on some mobile devices, we've decided to choose the safest route...
Dear friends,
I'm developing a prototype which use two NRF24L01+ and the auto ack and Enhanced ShockBurst only works with symmetrical data pipe address numbers.
Per...
Hello,
I want to try out the FDS according to this article .
My base project is the ble_app_uart (periph) from the SDK13 and I am using PCA10040 DK.
I enabled the...
Hello,
I saw that there is now serial dfu option enabled and Id like to make a serial DFU bootloader, however its a bit hard to read this Python code. Would be amazing...
If I want to use official devkits (like nRF51/2-DK) for a project do I need to test and certify them for FCC/CE?
Does FCC apply even on the software running on the device...
I just got nRF52 DEVELOPMENT KIT and NRF51822 BEACON KIT.
Can you tell me that where I can find the reference design for them and what could be the good starting point...
Hello, I am trying to program an BMD-300 using the NRF52-DK on a custom board,
The BMD300 is powered by the NRF52DK
BMD300 -> NRF52DK
SWDIO -> SH_SWDIO (pin 4) on...
