When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
I have purchased a red bear lab ble nano board with nrf51822 and a PICTAIL board with microchip RN4020 chip. i have set Tx power 4 for both boards. The rssi value shown in...
This may just be a preference or architecturing question but I thought I'd ask in case there was anything I'm not thinking of, or benefit of one or the other.
I have 2...
Hello,i am find an interesting phenomenon recently.I have a Nordic 5182 device(role as peripheral) and bonded to an iOS device(role as master),when i put the iOS device near...
I'm wondering, is it possible? This is what I think it will be like if it were going to be implemented:
Acquire the firmware from a host somewhere.
Since the payload...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am working with nrf51822 MC. In my Transmitter code, i am using in low power mode. I was enabled the low power in my code (__WFE(), __SEV(), __WFE()). I measuring...
Hello, I need HID device with NRF51 Dongle.
when NRF51 Dongle insert PC, PC will check it as HID device.
So, could anybody can share suggestion how to add HID on NRF51 Dongle...
Briefly:
Is it possible to switch LFCLKSRC to the internal RC from Xtal with WDT or RTC running? It appears I am only able to do this when Xtal is generating LFCLK...
I am trying to build a ibeacon device, but when iphone in "background mode", it can not get data from ibeacon device.
I used test code :examples\ble_peripheral\ble_app_beacon...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and Master Control...
