I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi team,
Iam using (\ble_tester\examples\ble_central\ble_app_hrs_c\pca10028) this example.i want to get rssi from the advertising beacon.
Iam using this functions
sd_ble_gap_scan_start...
I see on your website that Bluetooth 5 throughput numbers are given in the graph below. And the following disclaimer is given.
"Net data throughput not including overhead...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
hai
i have this code to save and read some data in flash.but the stored and read data are not same. always reads zeros. how can i solve that.........?
here is my code...
I'd like to be able to quickly update the advertising data using
sd_ble_gap_adv_data_set()
and at the moment I'm doing this via a bit of a hack, as I captured the advertising...
Normally, Raw data has TYPE (0x01), TYPE (0x09): device-name, TYPE (0X07): UUID 128 bits.
However, there are devices without TYPE (0x07).
Is this also a problem?
Communication...
Considering using an nRF52 module, I'm developing using EvoThings' native plugins right now. I don't think we have the resources to do IOS and Android native apps.
Has...
I have an application where my nrf52832 acts as a peripheral and I can connect to it without problems, but after some time like aprox 10 minutes when I try to connect to it...
Hi!
I have searched for this questoin, but not found anything useful. Probably I an not using a good search phrase.
How do I determine how much space is left on a nRF51...
This is a general question I will throw out initially, but I can get more specific if necessary. This is something I see a lot in my year or so of development with nordic...
SDK:8.1.0
Chip:51822AAHO
Hi,i use the nRF51822-PSV3.1 Schematic diagram.The chip set 4dbm tx power,
then i test the test point(C6) as follow,2402MHZ and 2426 MHZmax...
Hi,
I run the HID keyboad example, and a problem confuses me. I use the "lightblue" APP to connect the peripheral--"Nordic Keyboard", but the iphone appears a pairing box...
Hello!
I have been working recently with the PCA20006 Beacon board. The example we have tested is the ble_app_beacon that allow us to change the UUID/Major/Minor and go...
This may be a stupid question, but...
What value is BLE_GATTS_ATTR_LENS_MAX
Its mentioned a lot in the SDK, but I can't actually find a value for it actually defined...
