I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
I'm using an nRF52832 with the S132v2 and SDK 11 and wanted to test the ble throughput.
The nRF52832 should send as many as it can to an "normal" BLE-USB-Stick.
...
In SDK 11 the FreeRTOS port has the following line is declared in portmacro_cmsis.h
#define portNRF_RTC_PRESCALER ( (uint32_t) (ROUNDED_DIV(configSYSTICK_CLOCK_HZ, configTICK_RATE_HZ...
After updating from sdk11 to sdk12, the application only starts in debug. If started with reset, it hangs. I am running on a pca10028 board an with EmBlitz 1.0. NRF51 is QFACA1...
When I test the example, When I disconnect my phone of the nordic board.
I can use the other Phone to connect the nordic board
So, I think that how to avoid the connect...
I compile blinky_pca10040
I use IAR EWARM - ARM Cortex compiler
I have a Rigado BMD-300 on my PCB
Use J-LINK EDU
When I try to download and debug, I get the error
"Failed...
Hi
I came across this article:
www.nordicsemi.com/.../Bluetooth-Smart-hearing-aid-receives-stereo-audio-direct-from-iOS-devices-and-can-recognize-and-optimize-settings...
Hi, I want to change some configurations of my beacon such as packet type, UUID, Tx power and so on, in an online manner through the Bluetooth connection(by an application...
Hi I have run into this error when running. However it has just appeared (the FDS did work but now will not initilise.) I am using Visual_gdb.
As per this issue
I have...
Hi,
I am using nRF8001 with a MCU from PIC18F family. I have successfully configured nRF8001 to send and receive data through the nordic UART pipe (I used the app nRF UART...
I am experiencing a strange problem with stopping a scan. I am using the mesh from github.com/.../nRF51-ble-bcast-mesh together with interval scanning, meaning start scanning...
Hello Nordic developers,
I was tracing through the new SD init code in the HRS example app for nRF52 and followed this macro into softdevice_handler.h. Is it supposed to...
I am planning on using:
NRGF51822 CDAB WCSP (= 128KB Flash, 16KB RAM, 3.5x3.5mm)
Another main chip I will be using is:
LSM303AGR ( www.st.com/.../en.DM00177685.pdf)
...
