Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
When I use additional VS UUID, should I use sd_ble_uuid_vs_add(), se_ble_gatts_service_add() in order?
example,
sd_ble_uuid_vs_add(); <- VS1 UUID
se_ble_gatts_service_add...
Hello, I am developing with pc-ble-driver using python. I noticed that the Bluetooth connection becomes disconnected when I alt tab out of the gui I made. Is there a solution...
Hello,
I am using SEGGER Embedded Studio together with a nRF52832 and I am trying to read an EEprom register containing a 32-bit floating point value in four bytes (register...
Hi,
I try to use the BLE to send data to a smartphone but I have a issue when I try to flash my nRF52 DK, using eclipse. I get the following error :
No source available...
I am using the example ble central devices from the SDK 8.1. The example provided prints out to pin 19 (the on-board LED). I wanted to change the functionality to print to...
I am trying to add ADC to my program per the nordic examples on GitHub.
Using GCC, SDK12, nrf51.
These are the errors I am getting: (sorry for the formatting of this - code...
Hi,
SDK12 does not have Pstorage. I want to show you how to add it.
Steps:
Copy the pstorage folder in SDK11 into the SDK12 \components folder.
Open...
Hello,
I've been working on a project for some time now and prototyping it with replacement atmel ic's like the at mega328 and bluetooth modules and other stuff in the...
My custom board sometimes freezed on initialization process of bootloader (SDK11 dual_bank_ble_s130) when after long running and reconnect the power.
However the symptoms...
I am running the ble_app_hrs example and it runs as expected.
However, I tried removing one or more of the services from services_init as well as the corresponding advertisement...
I implement a card emulation and the card itself doesn't conform to 14443A-3 crc check. I need to disable crc check on card selected event
NRF_NFCT->RXD.FRAMECONFIG...
I've been running a hand soldered prototype board for about a week in an outdoor location where it gets hot and cold (mainly hot), and I noticed it was no longer visible on...
I am trying to add the spi and twi drivers to the ble_app_template project, but I keep running into errors. I am using the SDK 12.2.0. How are we supposed to go about adding...
Problem:
In our project we have one peripheral which can be bonded to many phones at the same time (of cause) while they are still close to it, thus connected via OS. ...
