Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello !
I have a problem with my program (on a nRF52 board) : when I send a value to the board via BLE, it seems that my static variables are reset.
I noticed that, because...
I need to store data in some moments and if something happen i have to read those data, i have to do a log events.
I use nrf51-dk and soft device s130. This data is taken...
"....\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production. Please see github.com/NordicSemiconducto.. . to generate it.
i found...
nrf51 dk with 51422 device (10028) was running in Segger Embedded Studio example imported from IAR / Keil ble_app_cscs_pca10028_s130 SDK12.1.0 was just fine. I loaded couple...
Hi,
I'm new and I'm a student.
I have to connect the adxl345z to my board mb39c811-evbsk-02.
It has an nrf51822 integrated.
Someone can explain which pin of i2c/Gpio i...
We wanted to update the firmware over the air, We needed help for zip file creation(.dat file, .bin file and .json file). There are many links online, We needed an link which...
Hi,
I'm developing to NRF81522 mcu, using a softdevice S130.
The MCU is connected to another device through the UART peripheral.
I'm encountering the next problems...
Hi,
I am getting data from sensor and want to replace some new data with the older one in flash using fds. Right now,firstly i will write into flash by using one different...
I am using the nRF toolbox to upload bootloader and firmware to a hardware project. Our project requires the number of packets (found within settings > nRF toolbox > Number...
Hi,
I am trying to flash the blinky example from nRF5_SDK_12.0.0_12f24da, the program compiles and is also downloaded to the NRF52 DK successfully. But the LEDs are not...
Hello.
I´ve got problems with a via BLE connected IMU and data transfer over UART.
I´ve now tried several methods to implement UART connection but with the given baudrate...
Getting the error when trying to compile the C++ project with SDK 12.1.0 :
In file included from .../components/softdevice/common/softdevice_handler/softdevice_handler...
We followed this link devzone.nordicsemi.com/.../ , we loaded zip file in mobile(android 6.0.1). We are able to select device, we are not able to select file(Zip). The issue...
as I found the sample code in sdk12 , the bootloader is quite different with bootloader in sdk11,
event uuid has got changed, is it possible to be compatible?
dual bank...
