Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
Hi,
I succeeded in implementing Channel sounding for multiple devices (based on previous samples). But now there is a little difference in how the data gets collected (buffer...
I have a project using BLE as a central on an nRF5340 to connect to several devices. For factory test I am being asked to implement something that can be used in the factory...
It would be helpful to know how a packet looks like when transmitted/received from the NRF9E5 chip. I already found the algorithm to build the correct CRC, expected from the...
I have included the DFU service and a custom service in my application. During initialisation DFU service is getting initialised and later down the line my custom service...
Hello,
I have few question please about this example.
m_lesc_private_key looks unused, how to modify source to use a pre shared private key ?
is this exemple secured...
Hi!
We are trying a new module with NRF24l01+. We find a troublesome thing. On this video you can see the RF communication starts and stops with a broad-spectrum signal...
Hi :
In my application, i need to use 2 spi master (SPI0,SPI1) and spi slave the same time, but when i compiled drivers_nrf/hal/nrf_spi.h and drivers_nrf/hal/nrf_spis.h...
Hi. I'm using nRF528332, SDK13, S132.
I'm making multi-link peripheral refering to "experimental_ble_app_multiperipheral".
This example code says as below.
#define...
Hi Nordic,
In my application, I want to consume as less power as I can. In the initialization I have this functions:
static void utils_setup(void)
{
APP_TIMER_INIT...
why not provide the ready-made tools？ like micro_ecc_lib_nrf52.lib and nrfutil.
because it 's really take user a lot of time to built these tools.
thank you.
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hello ! I'm beginning work with BLE . I have a project in which nrf51 is a central. App from smartphone will sending to central any key for example "3214941E0" when central...
Hello Nordic community,
I have a question about implementing DFU on the custom board. By looking at NRF52 DK and reading explanation in Nordic infocenter, I can see that...
Hi,
I am have a custom breakout board that uses the NRF52832 chip and I was able to program it using the J-link programmer and seperating ribbon cable to expose the Vtarg...
How do I maximize range for BT5?
I have two nRF52840 pdk units and I have loaded the ble_app_att_mtu_throughput app and tried it out. I have been seeing around 70 meters...
Hi. I tri to use my soft i2c lib
It works well at nrf51 and other mcu's. But nrf52 i2c_read doesnt works properly.
Other funcs works well.
When i read byte from i2c slave...
Hello
in the zephyr 1.7 release there have NRF52 and NRF51 porting without softdevice .
in the SDK 13 ,there has Freertos example working softdevice ,is there any plan...
