Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
I have been using the following parameters to flash program the example ble_app_uart_c_s130_pca10028 (SDK 9) but the problem is the it uses the S130 v1.0.0 softdevice...
Hi,
I have a newbie question. Is it possible to implement a POTS voice quality like an intercom system using Thread (assuming all the end points are using nrf52840 SOC...
We are trying to minimize the UART current in our product, so we tried some experiments on the PCA10040 board.
We noticed a significant current difference between SDK11...
SDK14.2.0 sd132v5.0.0 nRF52832
I've looked for a solution to my issue on the discussion forum, but can't find an answer. I am working with the buttonless DFU peripheral...
I have two nRF52832 devices. One of them I have been using for a while and the other is brand new. My BLE application will flash and run just fine on the old device but not...
Hello,
I read in your datasheet the follwoing:
"32.768 kHz synthesized from HFCLK (LFSYNT)
LFCLK can also be synthesized from the HFCLK clock source. The accuracy...
Hello,
in the Online Power Profiler , the current consumption increases, when the voltage is reduced. What is the reason for this?
Isn't there any documentation on the...
Hi
I need to capture a serial bit stream which consists of a sequence of 16 bit words, package them up and transmit over a bluetooth interface - it's a datalogger application...
Hi!
I have some troubles with making embedded serial port working on NRF52-DK. Basically I can receive data sent by nrf chip but I cant write. When I write something using...
More of a suggestion than a question:
Using the info available on the infoCenter, especially here and here , I'm trying to implement a way to dynamically select the DFU...
I use Adafruit Bluefruit library and developing code to run on Fanstell BT832.
Up to know i have been able to compile several examples and run it on the NRF52 DK board....
Hello! I am new to the Nordic and Bluefruit enviroments.
I am currently working on getting a scan response request from the scanner to the advertiser and have the advertiser...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
