Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Does nRF51822 have battery monitor?
pg 45 of datasheet says specifies "Absolute error when used for battery measurement" at:
Internal reference, input from VDD/3...
In the nrf52 OPS datasheet, for NVM and flash programming electrical specification (page 41) it has "Amount of writes in a block between erase" and Minimum for that is 181...
Hi all.
I need some suggestion how to use UART module in the nRF52 using nRF5_SDK_12.2.0 and the softdevice $132(it would affect?)
I would like use RX to receive information...
Hi.
Didn't find an exact answer for my question.
I'm using the ble_app_beacon example on my custom board based on nrf51822. While powering it from a coin battery, I measure...
Greetings. This is a followup to my previous question BLE Software Configuration for FCC Spurious Emissions . I did not ask the right question there and I did not want to...
Help!! I need to implement a dc motor position control and i have problem reading the encoder (too fast). I have seen that nrf51822 has a qdec peripheral. Any suggestions...
Hi,
I wanted to know if the UART pins can cause any issues if kept connected to usb (Rx/Tx pins stable to 3.3V) and directly to the GPIOs of the nRF52, while performing...
I've come across the following situation:
We have a device (nrf52) which uses fast advertising with whitelist after it has established a bond with a single phone. When...
Dear All,
I'm kinda getting desprate and would be very thankfull if somebody could help me.
I want to get two NRF24l01+ to communicate with each other. But it doesn...
hi, all
I met a communication problem between nrf52832 and nrf24le1, I used nrf52832 as receiver and nrf24le1 as transmitter, but unfortunately，nrf52832 can not receive...
We have a sensor product that has been in the field using the nRF8001 in no security required, just works mode for over a year. Recently, we had a request from a volume user...
I am using the ble_app_uart on the nrf51dk.RX is always enabled.I want to enable TX when data is to be transmitted and then disable it again.
I am using
NRF_UART0->TASKS_STOPTX...
Is there a way on the command-line to read the debug port (DP) register or access port (AP) register for nRF52 via the the nrjfprog program?
I do not want to write my own...
I'm new to the nRF51822. I've setup GCC and Make on Windows 10 and am using SDK 11. In all the examples of the SDK, flashing the newly made hex files (using GCC) with JLink...
