Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello folks,
we setup a new Project (eclipse,SKD 12.2.0, S130, NRF51822QFAAH0) based on the sdk examples. But the thing since 2 days we got a error we actually do not understand...
I have a PCA10040 board and downloaded SDK 12.2.0.
I am trying to being a project based on experimental_ble_app_eddystone. I can compile and upload the code to the board...
Problem:
IAR compiled hex file does not work for ble_app_hrs
Environment used:
IAR Embedded Workbench for ARM 7.80 Kickstart evaluation
nRF52 DK
Observation...
Hello,
I use, with success, the FDS library to save data to the flash memory. I also use, with success, the bootloader to update the application (original dual bank ble...
Hello there, thanks so much for taking the time to read. My problem is the following
I am trying to run GZP (Gazell Pairing Library). After successfully pairing with a...
We are currently trying to log our sensor data to a mobile phone through uart using nrfLogger app. We have nrf51 module and we are using SDK 12.
In nrfconnect, we select...
Hi,
I have problem with long write by sd_ble_gattc_write.
I send first 18 bytes by button on pca10028, then I waiting for BLE_GATTC_EVT_WRITE_RSP and sending rest of bytes...
I need some help with something very basic...
I need a way to upgrade my DFU BLE bootloader to either reset back to the app if no update has been sent after some timeout...
hello,
According to the "twi_scanner" example from the SDK12.2 I don't understand how the respective I2C pins/GPIOs are set up.
There is this function that I found "nrf_gpio_cfg...
My nRF52 device is an asset tracker and does not have a comm port. I have been looking at a BLE dongle setup for manufacturing test but the results are not repeatable with...
HI,
Nordic part used is nRF51822.
Is there any way to increase signal strength of BLE tx?
I see some parameters in advertising_init function for advdata.p_tx_power_level...
Hi all
According to chapter 50.2 of the nRF52832 product specification V1.2, the pins used for the UART peripheral should be configured before in the GPIO peripheral to...
why most of the examples of sdk 12's sdk config file has different options?
I'm trying to build an application that has Central and Peripheral Role application (and it...
Hi,
I have noticed the new preview DK for NRF82840 is now available, and the new chip is running the new BLE5 spec. My understanding on the BLE v5 is the higher data rate...
Dear Team,
We are facing an issue in nrf51822. We are compiling same project on different system in log file we got certain differences such as
System Licence
...
