Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I noticed that my current NRF52 based prototype is consuming 4.5mA as soon as I enable the BLE functionality, when its off its only 1.6mA
I send the chip to a sleep...
Hello !
I was wondering How the interval connection was calculated in the Android application nRF Connect ?
Do you use a special/ hided function ?
I tried to get it...
Hello,
I want to set up client and 3 servers which will send data from sensors to client with high data rate. Currently I am testing light switch example from Mesh SDK 1...
Hi,
I am using nrf51822 with SDK 12.2.0. As of now, we are using RL-51822-A1 for beacon as well as scanner.
But, we are not getting stable pattern for RSSI at 2m, 4m and...
Good day!
I am working on a custom board which has NRF52 and am using SDK 12.2.0 and in that, I want to stream BNO055 data. The base code I'm using is ble_app_hrs. The problem...
I want to set gpio using one interrupt and want to clear it using another interrupt funtion?
It seems i can only use the toggle funtion ,if i use the nrf_drv_gpiote_out_set...
Problem Statement: For one of our requirement we have to switch tx power in steps in ascending order continuously.
We are using ble_radio_notification feature to achieve...
Hi,
I'm trying to receive sensors data from three fdc1004 that have the same address. Can you have three TWI interfaces at the same time? How do you modify the nfr_drv_twi...
Hello,
I've just started using Segger Embedded Studio v3.30 for my development and I've been having trouble setting it up. I followed the instructions in this blog but...
Hi, I am programming on Thingy 52 to try to get it work like one of my nRF 52840 DK. Basically, I want Thingy to send beacons with data periodically and another Thingy to...
I have followed the tutorial given in the Nordic Devzone for using eclipse and haven't faced any problems while compiling and uploading the example "blinky".
I made sure...
Hi, ,
I am working on the nrf52832 development kit and want to program it as an I2C master. I have download the nRF SDK v12.3 but I am unable to understand the code written...
Hi guys
I am wondering what could be better for my system:
Multiples nRF52 central and peripherals (uart input/uart output to simulate keyboard and display)
SDK 13 ...
HI,
We use nrf52832 on a device with sdk 14.1.
Our product has to work at different temperature (between 20 and 70°C).
We did some measure and found this :
...
Hi, I have met an issue that the "ANT_CONFIG_TOTAL_CHANNELS_ALLOCATED" can't set more than 15 in ant_multi_channels example. Now I have a project that it need receive 100...
