after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hi,
I am using NRF51822 BLE. I wanted to know that when we put this BLE ic in sleep mode then, is there VDD_PA voltage is still 1.6V or it becomes shut off internally.??...
Is it possible to generate useful documentation from the provided .dox file ?
If I run doxygen.exe ble_api.dox I get some Latex and HTML output but looks incomplete because...
What would be the best way to go about sampling and transmitting a signal at 60 Hz? I am considering setting up notifications and a characteristic, but I don't think that...
Mac OS X 10.10 Yosemite rejects the format of the file system and puts it in a read only mode.
This issue was raised last October 24, 2014 at https://github.com/mbedmicro...
Hey guys,
Sorry to a basic question here, but it's been a few hours and I still can't get a connection to either of two brand new nRF51 dev boards, trying both on WindowsXP...
Hi Sir,
I’m working in an application with the demo board A to communicate via Bluetooth to the demo board B and send data between them. In the module I have to do send a...
I have a 51822-DK board. I have followed all of the instructions to set up the environment. Loaded all NRF tools, Keil v 5, install SDK. I began working on the examples. I...
Hello.
I need to hold 64-bit timer value. I store the 32-bit hardware timer value in one variable (low DWORD) and use an additional uint32_t variable as a an upper part of...
Hi, I'm having a bit of trouble getting the broadcast or HRM example to work. I'm using crossworks and after my last question, removed the retarget.c file and the code compiled...
I am new to smart beacon. We have to make a demonstration of our product i a short time. But I could'nt make it run. There are so many sosftdevice, bootloader and application...
Hi,
Basically, I have a DAC 7562 chip with inputs connected to pin 0.17(SYNC pin), 0.18(SCLK pin), 0.19(TX/Din pin), 0.13(CLR pin), 0.14(LDAC pin) with outputs connected...
I just recently upgraded to SDK 7.2.0 and am now using the keil pack installer as well. First of all, I really appreciate the ease of this new system, but I'm running into...
The new softdevice v8 states that previous revisions(1 and 2) don't support all the new features, and I'm curious how to determine what revision my ic is.
thanks,
akbar
