I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I am running the SDK12.2.0 ble_app_template peripheral example with RTT Logging enabled. The example seems to be running OK, but it logs: APP_ERROR:ERROR:Fatal with the ID...
Hi,
I am using NRF51822 to complete an application of multilink on one central . I tried to modify the central_link_count definition to 9 instead of 8, then I stuck on the...
Hello,
I am new on nRF51 and i would like to have a function to read the rotary position of motor in any rotary direction by adding a codewheel and a two channel reflective...
Hello,
I am trying to implement wake on motion functionality of MPU9250 with nRF52.
I am writing below sequence code for wake on motion configuration:
void MPU6500_StartMotionDetection...
Hi DevZone
I want to make a little beacon app, that advertises on channel 37 then waits 700 ms, advertises on channel 38, waits 700 and advertises on channel 39.
The below...
HI,
I wan't to read sensor data from ADC. So i use nrf_drv_saadc_sample() .
On Arduinos i usually call value = analogRead() and after that i process the data. But here the...
Hello,
We need to add custom data to advertise packet. As I understand we can use Manufacturer Specific Data. But to do this we need to get our Manufacturer ID from Bluetooth...
I have the following code for a custom service UUID and a custom 128 bit characteristic ID. I get a error of no memory available in our_char_init while adding the 128 bit...
Hi,
We bought a mac bd addr pool from IEEE
Where is the best way to store this mac adress during production ?
We guess the type will be: BLE_GAP_ADDR_TYPE_PUBLIC
Do...
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
Hi ,
I am trying to use the new softdevice SD130 V2.0.0 and have not had any luck when using the most recent version of SD130. I ran the same application with SD130 V1...
I've nrf51dk development board. It has nrf51422QFACA10 chip and has 32kB ram and 256kB flash. I downloaded sdk V11 and programmed ble_app_beacon_s130_pca10028. It worked fine...
I try to move my project from Keil to GCC but I get some different behavior. To show the difference I use examples/ble_peripheral/ble_app_uart
The part of the code below...
