Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hi all,
I am using an NRF52 and SDK 13.0
I have an external device (central) that I am connecting to using my (peripheral) device.
My peer manager set up is
#define...
Hello All,
I've got two Rigado development boards that I'm programming with KEIL uvision 5. I've tried a few examples, for example: blinky, which program and work fine...
Hello
I want to clarify the exact meaning of the carrier test or unmodulated signal in DTM.
In carrier test mode, DUT transmits 0xFFF....FFF which means all one pattern...
Hello,
For my project I need to measure the battery voltage while transmitting data to get a good indication of the battery capacity. I've found an old example ( link text...
Hi,
nRF24L01 seems like a perfect choice for home automation project that I have in mind .. I will have to install about 20 of those around the house.
My question is...
Hello,
I'm working on the bootloader using SDK13.1. In the file dfu_req_handling.c there is a variable called m_flash_operations_pending that gets incremented with every...
HI,
I am very new to this, I am looking to put a video or flash player or another image to to load into my nRF51822 beacon kit. I am thinking the straightaway method would...
Hi,
I am working with ble_app_uart code, in that I am trying to configure different baud rates like 9600,38400 and 57600. With these baud rates I am not getting any issues...
Hi
sd_ble_gattc_primary_services_discover() is being called from ble_db_discovery_start() within ble_db_discovery.c. I'm trying to get the ble_cts_c service working. It...
Hi
I am receiving INVALID_STATE (error code 8) from ble_db_discovery_start. According to documentation, this error can be returned "If this function is called without calling...
Hi, i have just bought a NRF51 DK. I have tried to run the precompiled Blinky example. I have first installed NRFGo Studio. I connected the board. In NRFGo Studio, I selected...
Hello,
I am making a battery service to report the battery that is sampled by the SAADC, so far I am am able to compile it and debug it, however I see how my saadc_event_handler_interrupt...
Hi
I'm reading the debug output of ble_cts_c.c:
NRF_LOG_DEBUG("BLE event handler called with event 0x%x\r\n", p_ble_evt->header.evt_id);
However I can't find any...
The analog circuits 51822 and rfx2411n supplied by the authorities are connected 52832, but the circuit is not working properly.PA and LNA switching has been controlled in...
This is to build upon a previous question i had here .
This time, I am having issues with SDK 14.
I can compile and run the BLE peripheral HRS example fine. With SDK 14...
